[Search for users]
[Overall Top Noters]
[List of all Conferences]
[Download this site]
| Title: | DIGITAL UNIX (FORMERLY KNOWN AS DEC OSF/1) |
| Notice: | Welcome to the Digital UNIX Conference |
| Moderator: | SMURF::DENHAM |
|
| Created: | Thu Mar 16 1995 |
| Last Modified: | Fri Jun 06 1997 |
| Last Successful Update: | Fri Jun 06 1997 |
| Number of topics: | 10068 |
| Total number of notes: | 35879 |
9113.0. "V4.0B build help" by TEACH::DAN () Tue Mar 11 1997 15:17
I'm trying to build Digital Unix V4.0B on an Alphaserver 1000A 5/133. I'm
using the serial port for my console device. Below is the >>>show config
from the console followed by the attempt to boot up standalone Unix from
the CD. The boot dies complaining abount "no serial driver". I do have the
console variable "console" set to serial and I've powered off/on.
Any ideas?????
thanks,
dan
=============================================================================
>>>SH CONF
Digital Equipment Corporation
AlphaServer 1000A 5/333
Firmware
SRM Console: V4.7-169
ARC Console: 5.23
PALcode: VMS PALcode V1.19-3, OSF PALcode V1.21-5
Serial Rom: V1.0
Processor
DECchip (tm) 21164A-1 333MHz
Memory
128 Meg of System Memory
Bank 0 = 128 Mbytes(32 MB Per SIMM) Starting at 0x00000000
Bank 1 = No Memory Detected
Bank 2 = No Memory Detected
Bank 3 = No Memory Detected
Slot Option Hose 0, Bus 0, PCI
7 Intel 82375EB Bridge to Bus 1,
EISA
8 DECchip 21050-AA Bridge to Bus 2,
PCI
12 DECchip 21140-AA ewa0.0.0.12.0 00-00-F8-03-3E-EB
13 DEC KZPSA pkc0.7.0.13.0 SCSI Bus ID 7
dkc100.1.0.13.0 RZ26N
dkc200.2.0.13.0 RZ26N
dkc300.3.0.13.0 RZ26N
Slot Option Hose 0, Bus 1, EISA
Slot Option Hose 0, Bus 2, PCI
0 QLogic ISP1020 pka0.7.0.2000.0 SCSI Bus ID 7
dka0.0.0.2000.0 RZ28M
dka100.1.0.2000.0 RZ28M
dka500.5.0.2000.0 RRD45
1 DEC KZPSA pkb0.7.0.2001.0 SCSI Bus ID 7
2 DEC PCI MC Rev: e, mca0
Slot Option Hose 0, Bus 0, PCI
7 Intel 82375EB Bridge to Bus 1,
EISA
8 DECchip 21050-AA Bridge to Bus 2,
PCI
12 DECchip 21140-AA ewa0.0.0.12.0 00-00-F8-03-3E-EB
13 DEC KZPSA pkc0.7.0.13.0 SCSI Bus ID 7
dkc100.1.0.13.0 RZ26N
dkc200.2.0.13.0 RZ26N
dkc300.3.0.13.0 RZ26N
Slot Option Hose 0, Bus 1, EISA
Slot Option Hose 0, Bus 2, PCI
0 QLogic ISP1020 pka0.7.0.2000.0 SCSI Bus ID 7
dka0.0.0.2000.0 RZ28M
dka100.1.0.2000.0 RZ28M
dka500.5.0.2000.0 RRD45
1 DEC KZPSA pkb0.7.0.2001.0 SCSI Bus ID 7
2 DEC PCI MC Rev: e, mca0
>>>boot dka500
(boot dka500.5.0.2000.0 -flags 0)
FRU table creation disabled
block 0 of dka500.5.0.2000.0 is a valid boot block
reading 16 blocks from dka500.5.0.2000.0
bootstrap code read in
base = 1ca000, image_start = 0, image_bytes = 2000
initializing HWRPB at 2000
initializing page table at 7ff0000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
Digital UNIX boot - Fri Nov 15 21:24:46 EST 1996
Loading vmunix ...
Loading at fffffc0000230000
Current PAL Revision <0x1000300010113>
Switching to OSF PALcode Succeeded
New PAL Revision <0x1000500020115>
Sizes:
text = 4769280
data = 1253168
bss = 2497296
Starting at 0xfffffc0000404240
Alpha boot: available memory from 0xc9a000 to 0x7fee000
Digital UNIX V4.0B (Rev. 564); Sat Nov 16 00:01:00 EST 1996
physical memory = 128.00 megabytes.
available memory = 115.35 megabytes.
using 161 buffers containing 1.25 megabytes of memory
Firmware revision: 4.7
PALcode: OSF version 1.21
AlphaServer 1000A 5/333
Mem_size = 132268032, consmem = 238
pci0 at nexus
eisa0 at pci0
pci2000 at pci0 slot 8
isp0 at pci2000 slot 0
isp0: QLOGIC ISP1020A
cam_logger: CAM_ERROR packet
cam_logger: bus 0
isp_probe
NVRAM parameters invalid, using driver Fast10 defaults
isp0: Firmware revision 2.10 (loaded by console)
scsi0 at isp0 slot 0
rz0 at scsi0 target 0 lun 0 (LID=0) (DEC RZ28M (C) DEC 0616)
(Wide16)
rz1 at scsi0 target 1 lun 0 (LID=1) (DEC RZ28M (C) DEC 0616)
(Wide16)
rz5 at scsi0 target 5 lun 0 (LID=2) (DEC RRD45 (C) DEC 0436)
pza0 at pci2000 slot 1
pza0 firmware version: DEC P01 A10
scsi1 at pza0 slot 0
tu0: DECchip 21140-AA: Revision: 2.0
tu0: auto negotiation capable device: National DP83840
tu0 at pci0 slot 12
tu0: DEC Fast Ethernet Interface, hardware address: 00-00-F8-03-3E-EB
tu0: auto negotiation off: selecting 10BaseT (UTP) port: half duplex
pza1 at pci0 slot 13
pza1 firmware version: DEC P01 A10
scsi2 at pza1 slot 0
scsi2 at pza1 slot 0
rz17 at scsi2 target 1 lun 0 (LID=19) (DEC RZ26N (C) DEC 0616)
(Wide16)
rz18 at scsi2 target 2 lun 0 (LID=20) (DEC RZ26N (C) DEC 0616)
(Wide16)
rz19 at scsi2 target 3 lun 0 (LID=21) (DEC RZ26N (C) DEC 0616)
(Wide16)
gpc0 at eisa0
No FRU table entry found in console-rpb
--Not creating a FRU table errorlog packet
configure_console: No serial driver from get_info
No kernel console driver installed
vm_swap_init: warning /sbin/swapdefault swap device not found
vm_swap_init: swap is set to lazy (over commitment) mode
panic (cpu 0): System does not have a console configured.
syncing disks... done
DUMP: No primary swap, no explicit dumpdev.
Nowhere to put header, giving up.
CP - SAVE_TERM routine to be called
CP - SAVE_TERM exited with hlt_req = 1, r0 = 00000000.00000000
halted CPU 0
halt code = 5
HALT instruction executed
PC = fffffc0000405cb0
>>>
| T.R | Title | User | Personal
Name | Date | Lines |
|---|
| 9113.1 | | netrix.lkg.dec.com::thomas | The Code Warrior | Tue Mar 11 1997 19:09 | 2 |
| Did you run the OSF/VMS ECU? Was this a NT system? If so, you need to run
ECU to generate the entries required by OSF (like the console).
|
| 9113.2 | it works now | TEACH::DAN | | Wed Mar 12 1997 09:35 | 6 |
| Yes, it was configured for NT. I had ">>>runecu" to switch to UNIX but
I had forgotten to load the VMS/UNIX ECU floppy.
I works fine now...thanks for your help.
dan
|