| Title: | DEChub/HUBwatch/PROBEwatch CONFERENCE |
| Notice: | Firmware -2, Doc -3, Power -4, HW kits -5, firm load -6&7 |
| Moderator: | NETCAD::COLELLA DT |
| Created: | Wed Nov 13 1991 |
| Last Modified: | Fri Jun 06 1997 |
| Last Successful Update: | Fri Jun 06 1997 |
| Number of topics: | 4455 |
| Total number of notes: | 16761 |
Customer has two DECConcentrator 900MXs both in DEChub One-MX docking
stations. Frimware revision is 3.3.2 on both conectrators.
One concentrator was configured as Stump AB and the other as Trunk AB.
He also has a Cisco 7000 setup with A and B out (something like Stump AB??).
When he connects from A from the Cisco to B of Stump AB, from A of Stump AB
to B of Trunk AB, then A of Trunk AB back to Cisco B.... B of Trunk AB rejects
the connection to Stump AB and the PHY light goes out and the Trunk AB unit is
no longer reachable via SNMP (ClearVISN).
A Cisco 7000 B
| |
| |
B A
[Stump AB] [Trunk AB]
A B
| |
+--------------------------------+
****
PHY light goes
out on this port!
The customer tried this as a test configuration. Since this didn't work, he
went back to both concentrators setup as Stump AB and everything worked. He
used the existing fiber cables, simply moving them from the front to the back.
Shouldn't this have worked?
What he wants to do is convert both concentrators to Trunk AB allowing more
front M ports and eventually "merging" this ring with another dual ring.
Any input would be appreciated!
-jas
[Posted by WWW Notes gateway]
| T.R | Title | User | Personal Name | Date | Lines |
|---|---|---|---|---|---|
| 4417.1 | Dual ring should work front or back | SNOFS1::KHOOJEANNIE | Laziness breeds Efficiency | Fri May 16 1997 02:52 | 13 |
Just a long shot ... is he trying the correct front panel ports (1 is A
and 6 is B) and DEChub ONE-MX ports?
A/M B/S
DEChub ONE-MX
DECconc900MX
1-A/M 2-M 3-M 4-M 5-M 6-B/S/M
Regards
Jeannie
| |||||
| 4417.2 | It should work. | NETCAD::ARGO | Fri May 16 1997 09:15 | 4 | |
The configuration should work. Have your customer remove the Cisco from the configuration until we figure out what the problem is. Also, make sure the DEChub-ONE connections are from A-B and B-A. Dennis | |||||
| 4417.3 | 80 columns | NETCAD::COLELLA | Shipping is a feature. | Fri May 16 1997 10:41 | 14 |
And for the 80 column folks among us:
================================================================================
-< It should work. >-
--------------------------------------------------------------------------------
The configuration should work. Have your customer remove the Cisco from
the configuration until we figure
out what the problem is. Also, make sure the DEChub-ONE
connections are from A-B and B-A.
Dennis
| |||||
| 4417.4 | I see.... | NNTPD::"[email protected]" | Jeff Smith | Fri May 16 1997 11:20 | 19 |
re: .1 I'm not sure I understand the question.... The connection goes out of the front of one concentrator and into the back of the other one, the out of the back of that concentrator to the Cisco 7000. re: .2/.3 Pardon my drawing...it didn't translate very well through the notes gateway... I gather then that there isn't an engineering (or other) reason that using the front ports on one DC900 and the back ports of a DC900/DEChub One-MX in the same dual ring. I also gather that you suspect an issue with the Cisco 7000? Can you elaborate? [Posted by WWW Notes gateway] | |||||