[Search for users] [Overall Top Noters] [List of all Conferences] [Download this site]

Conference netcad::hub_mgnt

Title:DEChub/HUBwatch/PROBEwatch CONFERENCE
Notice:Firmware -2, Doc -3, Power -4, HW kits -5, firm load -6&7
Moderator:NETCAD::COLELLADT
Created:Wed Nov 13 1991
Last Modified:Fri Jun 06 1997
Last Successful Update:Fri Jun 06 1997
Number of topics:4455
Total number of notes:16761

3778.0. "Cannot set up PVCs using clearVISN MultiChassis Manager" by LEMAN::JRS (John SHADE - 'Attila the Nun') Wed Aug 07 1996 05:54

I am posting this note on behalf of a colleague who is in the fortunate
position of being on holiday:

=================
I installed ClearVISN on the customer's PC running Window NT (v. 3.5.1) and 
we tried to establish PVCs with one of its GUIs. However, we did not succeed. 

I reproduced the same problem with my PC. The error message we got after having
entered the parameters and pressed APPLY, was like this --"Invalid Action : 
View Message Box", and the Message box said, "attemp to create PVC link 
failed ...". And then, another error message appeared in a stand alone window, 
"System or general error".

These error messages do not tell me what I have done wrong. Did anybody get 
it to work?

Thanks in advance!

Yu-Hong
T.RTitleUserPersonal
Name		DateLines
3778.1NETRIX::"[email protected]"Jae KoWed Aug 07 1996 11:207
There are a number reasons for this, which can relate to "NO SUCH" from SNMP.
Please provide as much information as possible such as configuration,
input parameters, SNMP trace/log, etc.. and with this can help identify the
problem.

[Posted by WWW Notes gateway]
3778.2A simpler testLEMAN::PAIVAHawkeye - Network Support @GEOTue Aug 20 1996 09:1417
    Having tried to modify the "Admin status" from "green" to "red" of a
    pt-pt PVC (Port 1.1 VPI/VCI 0/103 to Port 4.3 VPI/VCI 0/403) created
    through the console of the GS/ATM I got the following in the message box:
    
    [E] Attempt to Modify PVC Status failed T:1 SP:0.0 VCC:0-0 To SP:0.0
    VCC:0-0
    
    Is this helpful?
    
    My first feeling is that MCM is not ready to execute this kind of
    operation...?!
    
    Cheers,
    
    Pedro
3778.3NETRIX::"[email protected]"Jae KoTue Aug 20 1996 18:3032
 I added the point to point PVC as follows:

        Input Virtual Circuit Parameters:

        Enter desired slot (1-6,8-14) for input: 4
        Enter desired port for input: 3
        Zero as input results in a system provided PVC/SVC VCI
        Enter vci input : 103

        Output Virtual Circuit Parameters:

        Enter desired slot (1-6,8-14) for output: 4
        Enter desired port for output: 4
        Zero as input results in a system provided SVC/PVC VCI
        Enter vci output : 103
        Determine desired CBR bandwidth, in Megabits/sec. (max: 126)
        Enter bandwidth, zero will result in an ABR circuit: 0
        Should this be a duplex circuit, y or n (y)?:
        Should this be a FLOWmaster circuit at the input, y or n (y)?:
        Should this be a FLOWmaster circuit at the output, y or n (y)?:

        Circuit established between 4.3 Invci: 103 and 4.4 Outvci: 103

        Commit permanent virtual circuit to non-volatile storage, y or n (n)?: y

        Point-to-Point PVC Record committed to flash successfully.

   

  Refreshed PVC screen with MCM and successfully modified the admin status
  
[Posted by WWW Notes gateway]
3778.4Are we talking about the same stuff?LEMAN::PAIVAHawkeye - Network Support @GEOTue Aug 27 1996 05:4010
    re: .3
    
    I suppose you used the GS/ATM console to set up the PVCs. When in MCM,
    did you get into the PVC summary and then selected a PVC to modify (in
    which you would modify the "admin status")?
    
    Cheers,
    
    Pedro
3778.5NETRIX::"[email protected]"Mon Sep 09 1996 17:054
   Yes set up PVC with GS and modify admin status with MCM.
   
    Jae Ko
[Posted by WWW Notes gateway]