| Title: | DEChub/HUBwatch/PROBEwatch CONFERENCE |
| Notice: | Firmware -2, Doc -3, Power -4, HW kits -5, firm load -6&7 |
| Moderator: | NETCAD::COLELLA DT |
| Created: | Wed Nov 13 1991 |
| Last Modified: | Fri Jun 06 1997 |
| Last Successful Update: | Fri Jun 06 1997 |
| Number of topics: | 4455 |
| Total number of notes: | 16761 |
Hi,
I am having a few problems with a DECbridge 90. I want to set it up, so only LAT (60-04) is
forwarded. I put the bridge in "invert mode", as the manual suggests: enabling a filter to forward
the desired protocol should block all other protocols, except those defined to be forwarded.
After I did that, I could see with a protocol analyzer, that everything was being forwarded
(DECnet, NetBeui, TCP/IP, etc...). Is that a BUG or did I miss something in my configuration?
Another question is: How can I set up a filter to block NetBeui?
Thanks in advance for any help. Regards,
Roberto
===============================================================================================
DECbridge> SHOW BRIDGE
DECbridge 90 V1.14 08-00-2B-2F-2C-E4 � 1991 Digital Equipment Corp
FPROM V3.9 �1991,94 Digital Equip Corp 28-SEP-94
Bridge states:
Console owner: AA-00-04-00-93-50 Uptime: 4,868.75 seconds
Bridge state: 17 Work group size: 7
Hub mgmt enable: 1 Spanning tree enable: 1
Flash ROM erasures: 3 Address lifetime: 450*2 sec.
Event counters:
Sys buffer unavail. errors: 0
WG size exceeded errors: 0
Spanning tree parameters:
Bridge id: FF-FF-08-00-2B-2F-2C-E4 Root port: 0
Designated_root: FF-FF-08-00-2B-2F-2C-E4 Root path cost: 0
Current Forward delay: 15, Hello interval: 1, Listen time: 15
Def. Forward delay: 15, Hello interval: 1, Listen time: 15
Topology change flag: 0 Topology change timer: 30
Bad hello limit: 15 Bad hello reset interval: 5
Epoch_mode: 3 Epoch1 who: 00-00-00-00-00-00 Mode changes: 0
Epoch 1 poll time: 18 seconds Epoch 1 response time: 15 seconds
| T.R | Title | User | Personal Name | Date | Lines |
|---|---|---|---|---|---|
| 3048.1 | Re-formated for the 80 column challenged... | NETCAD::BATTERSBY | Fri Dec 08 1995 12:59 | 48 | |
<<< NETCAD::KALI$USER3:[NOTES$LIBRARY]HUB_MGNT.NOTE;1 >>>
-< DEChub/HUBwatch/PROBEwatch CONFERENCE >-
================================================================================
Note 3048.0 Problems with DECbridge 90 filtering No replies
PCSUP1::ventriglia 40 lines 8-DEC-1995 12:52
--------------------------------------------------------------------------------
Hi,
I am having a few problems with a DECbridge 90. I want to set it up, so only
LAT (60-04) is forwarded. I put the bridge in "invert mode", as the manual
suggests: enabling a filter to forward the desired protocol should block all
other protocols, except those defined to be forwarded.
After I did that, I could see with a protocol analyzer, that everything was
being forwarded (DECnet, NetBeui, TCP/IP, etc...). Is that a BUG or did I
miss something in my configuration?
Another question is: How can I set up a filter to block NetBeui?
Thanks in advance for any help. Regards,
Roberto
===============================================================================
DECbridge> SHOW BRIDGE
DECbridge 90 V1.14 08-00-2B-2F-2C-E4 � 1991 Digital Equipment Corp
FPROM V3.9 �1991,94 Digital Equip Corp 28-SEP-94
Bridge states:
Console owner: AA-00-04-00-93-50 Uptime: 4,868.75 seconds
Bridge state: 17 Work group size: 7
Hub mgmt enable: 1 Spanning tree enable: 1
Flash ROM erasures: 3 Address lifetime: 450*2 sec.
Event counters:
Sys buffer unavail. errors: 0
WG size exceeded errors: 0
Spanning tree parameters:
Bridge id: FF-FF-08-00-2B-2F-2C-E4 Root port: 0
Designated_root: FF-FF-08-00-2B-2F-2C-E4 Root path cost: 0
Current Forward delay: 15, Hello interval: 1, Listen time: 15
Def. Forward delay: 15, Hello interval: 1, Listen time: 15
Topology change flag: 0 Topology change timer: 30
Bad hello limit: 15 Bad hello reset interval: 5
Epoch_mode: 3 Epoch1 who: 00-00-00-00-00-00 Mode changes: 0
Epoch 1 poll time: 18 seconds Epoch 1 response time: 15 seconds
| |||||
| 3048.2 | NPSS::RAUHALA | Tue Dec 26 1995 18:10 | 1 | ||
what does the LIST PROTOCOL command show?? | |||||