| Title: | DEChub/HUBwatch/PROBEwatch CONFERENCE |
| Notice: | Firmware -2, Doc -3, Power -4, HW kits -5, firm load -6&7 |
| Moderator: | NETCAD::COLELLA DT |
| Created: | Wed Nov 13 1991 |
| Last Modified: | Fri Jun 06 1997 |
| Last Successful Update: | Fri Jun 06 1997 |
| Number of topics: | 4455 |
| Total number of notes: | 16761 |
Hi,
I have a customer who is implementing large numbers of Multi-switch
900's and are using HUbwatch for Windows 3.1 and NDUPLUS 1.0. When
upgrading the hubs using NDUPLUS and the commands for HUBMANV2 to slot
9 of the hub, this works fine for 2.1 MAM to 3.1 MAM. When the
customer try's to upgrade from V3.0 MAM to V3.1 MAM this command fails
with "wrong version error". The customer has tried using HUBMANV3 in
their command with same failure and has tried the command for
standalone IP device with same failure (they tried standalone IP
commands for V2.1 MAM to V3.1 MAM and this worked so they know the commands
are OK. Currently they have three backplanes they are ready to ship
back as bad unless there is some way to upgrade form V3.0 MAM. Any
suggestions or ideas? If you have upgraded from V3.0 to 3.1
successfully under NDUPLUS 1.0 for DOS please include the commands you
used which I will relay to the customer. Thanks in advance.
Ted Breimayer
| T.R | Title | User | Personal Name | Date | Lines |
|---|---|---|---|---|---|
| 1989.1 | Works OK for me | ROGER::GAUDET | Because the Earth is 2/3 water | Thu Feb 09 1995 13:45 | 44 |
Ted, I must admit that I've never seen that error message from DECndu Plus. I just tried this on one of our hubs and it worked just fine. What version of DOS is the customer running when attempting the upgrade? Here's the command log from my successful attempt: A:\> decndup /V (c) Digital Equipment Corporation. 1993. All Rights Reserved. DECndu Plus (Network Device Upgrade) Utility V1.0 for DOS A:\> decndup /s 16.21.2.83 (c) Digital Equipment Corporation. 1993. All Rights Reserved. [SYSDESCR] Getting Device INFO (sysDescr) Hub900MultiSwitch,DEChub 900 MultiSwitch,HW=F,RO=V1.1.6,SW=V3.0.0 DECnduPlus: SUCCESS A:\> decndup /u /f hubmanv2 /m 9 16.21.2.83 c:\firmware\dmhub310.bin [HUBMANV2] Getting sysDescr Hub900MultiSwitch,DEChub 900 MultiSwitch,HW=F,RO=V1.1.6,SW=V3.0.0 [HUBMANV2] Setting (ChasLoadEntryStatus) to CreateRequest (2) [HUBMANV2] Set load host IP address (ChasLoadIpHostAddr) 16.21.16.121 [HUBMANV2] Setting load filename c:\firmware\dmhub310.bin [HUBMANV2] Setting ChasLoadEntryStatus) Valid (1) [HUBMANV2] Setting (ChasLoadAdminStatus) Start-read (2) [HUBMANV2] STARTING TFTP SERVER BLOCKNo = 959 BYTES = 490496 [HUBMANV2] TFTP DOWNLOAD COMPLETED DECnduPlus: SUCCESS ..... after waiting a few minutes for the new code to be written to FLASH ..... A:\> decndup /s 16.21.2.83 (c) Digital Equipment Corporation. 1993. All Rights Reserved. [SYSDESCR] Getting Device INFO (sysDescr) Hub900MultiSwitch,DEChub 900 MultiSwitch,HW=F,RO=V1.1.6,SW=V3.1.0 DECnduPlus: SUCCESS | |||||
| 1989.2 | tested now in my favorite PC and HUB | PRSSOS::PEYRACHE | Jean-Yves Peyrache Country Support Group France | Thu Feb 09 1995 14:02 | 8 |
C>DECNDUP /u /f hubmanv2 /m 9 x.x.x.x c:\firmware\dmhub310.bin x.x.x.x equal address ip of your hub900 hope that's help you jean-yves | |||||