Conference netcad::hub_mgnt

1903.0. "DECbridge 900MX " Error Code 0000013B "" by CERN::HAUSHERR () Wed Jan 18 1995 11:05

DECbridge 900MX is crashing with " Error Code 0000013B "

The Bridge is connected on a Single Hub. 

Can anybody tell me whats " Error Code 0000013B "

Below you can find the dumps .

	Roland
==========================================================================
                           Enter selection : 3

DECbridge 900MX
==============================================================================

DECbridge 900MX, 6-Ethernet/FDDI Bridge, HW=v0/2,RO=v0.2,SW=v1.4.0
SysUpTime                                 : 00:38:33   20 resets
SNMP Read/Write Community                 : public
SNMP Trap Addresses                       : 128.141.201.45
Status of Last Downline Upgrade           : No Status
In-Band Interface Hardware Address        : 08-00-2B-B0-D2-F7
In-Band Interface IP Address              : 128.141.249.29
In-Band Iefault Gateway Address 	  : 128.141.200.10
Out-of-Band (OBM) Interface IP Address    : Not Configured
Out-of-Band (OBM) Management Port Speed   : 9600
Port 4 using front panel UTP port

==============================================================================

                                DUMP ERROR LOG
                            Current Reset Count: 20

==============================================================================


Entry #       = 3
Entry Status  = 0   [0=valid, 1=write_error, 2=invalid, 3=empty, 4=crc_error
Entry Id      = 10
Firmware Rev  = 1.4
Reset Count   = 19
Timestamp     =    0    0  1A1
Write Count   = 9
FRU Mask      = 0
Test ID       = DEAD
Error Data    = SR=2100 PC=0303646E Error Code=0000013B ProcCsr=7F6D
Registers     = D0=00002000 D1=00002100 D2=00000800 D3=00002000
                D4=00000001 D5=0000015A D6=808D002C D7=0000002A
                A0=02000000 A1=02000000 A2=0444A484
Dump another entry [Y]/N?
Entry #       = 2
Entry Status  = 0   [0=valid, 1=write_error, 2=invalid, 3=empty, 4=crc_error
Entry Id      = 10
Firmware Rev  = 1.4
Reset Count   = 18
Timestamp     =    0    0  E4E
Write Count   = 9
FRU Mask      = 0
Test ID       = DEAD
Error Data    = SR=2100 PC=0303646E Error Code=0000013B ProcCsr=776D
Registers     = D0=00002000 D1=00002100 D2=00000800 D3=00002000
                D4=00000001 D5=000000FC D6=808D002C D7=0000002A
                A0=000547EE A1=0006B7CC A2=0444D882 A3=0444D8A4
                A4=0444D882 A5=00056110 A6=0004A6B0 A7=0004A6A0
Dump another entry [Y]/N?
Entry #       = 1
Entry Status  = 0   [0=valid, 1=write_error, 2=invalid, 3=empty, 4=crc_error
Entry Id      = 10
Firmware Rev  = 1.4
Reset Count   = 17
Timestamp     =    0    0 B1EC
Write Count   = 9
FRU Mask      = 0
Test ID       = DEAD
Error Data    = SR=2100 PC=0303646E Error Code=0000013B ProcCsr=7F6D
Registers     = D0=00002010 D1=00002100 D2=00000800 D3=808D2010
                D4=00000001 D5=0000002A D6=00000005 D7=00000000
                A0=02000000 A1=02000000 A2=0444D800 A3=04256800
                A4=0004A7A0 A5=0444D800 A6=0004A714 A7=0004A704
Dump another entry [Y]/N?
    

    This error code indicates that the bridge is receiving large packets
    addressed to its own DA.  Its a known problem and fixed in the next wave.
                                        
    Is anyone pinging the bridge with large packets or an NMS that could be 
    sourcing large packets?  You may need to isolate this to a segment and
    get a trace of all packets with the DA of the bridge prior to the reset.  
                                                                  
    Bill

Bill,

Thanks for the fast reply.

We will install a Data Analyzer to find out who is pinging the bridge
with large packets.

Can you tell me : When can we expect the next release with this problem
fixed  ??

	Roland