[Search for users] [Overall Top Noters] [List of all Conferences] [Download this site]

Conference netcad::hub_mgnt

Title:DEChub/HUBwatch/PROBEwatch CONFERENCE
Notice:Firmware -2, Doc -3, Power -4, HW kits -5, firm load -6&7
Moderator:NETCAD::COLELLADT
Created:Wed Nov 13 1991
Last Modified:Fri Jun 06 1997
Last Successful Update:Fri Jun 06 1997
Number of topics:4455
Total number of notes:16761

1097.0. "Hubwatch and DS90TL" by DRAC::LEFERNANDEZ (LUIS ELOY FERNANDEZ) Thu Jun 09 1994 13:26

    Hi everybody,
    
    
    my name is Luis Eloy, from DECsite Barcelona (Spain). We are having
    some trouble with a DEChub 900MS, Hubwatch 2.0 (Windows) and 
    DECservers 90TL.
    
    1. When the DECservers 90TL load software, the DEChub900 MS display
    shows the following message: "DECserver 90TL, non fatalfailure".
    All DECservers 90TL work fine.
    
    If software is not loaded, the message is "DECserver 90TL up".
    
    2. Unable to access DECservers 90TL from Hubwatch. Internet addresses
    are OK, and we are able to "ping" from DECserver to the PC running
    Hubwatch. The message we get is: "Agent does not respond".
    
    DEChub 900MS revisions: Hardware version F
    			    ROM revision V1.1.6
    			    Firmware revision V2.2.1
    DECserver 90TL revs.:   FW 2.0.0
    			    HW 3.0
    DECserver 90TL software is V1.1 BL44-10 
    
    We have two DEChub 900MS, with 4 repeaters 900TM and 5 DECservers 90TL
    and 5 repeaters 900TM and 4 DECservers 90TL.
    
    
    	Thanks in advance,
    
    
    					Luis
T.RTitleUserPersonal
Name		DateLines
1097.11st PassNACAD2::DRAGONThu Jun 09 1994 16:0415
    
    Luis,
    
    	The non fatalfailure error on the MAM LCD is expected. It has to do
        with the DECserver 90TL not responding to "who are you?" requests
        on the mamagement bus after it loads its code. As for your
        inability to reach the server's agent, you might want to check 
        section 3.6.3 of the "HUBwatch Installation and Configuration" 
        manual to be sure that your server's are setup correctly (ie
        SNMP enabled, GET, GETNEXT, SET enabled, etc.). If they're setup 
        correctly we'll have to dig deeper.  
    
    Hope this helps,
    Bob
1097.21st pass doneDRAC::LEFERNANDEZLUIS ELOY FERNANDEZFri Jun 10 1994 02:5912
    Hi Bob,
    
    we did check and change those parameters, as stated on the installation
    manual.
    
    What else can we look for?
    
    Thanks,
    
    							Luis
1097.3Another PossibilityLEVERS::DRAGONMon Jun 13 1994 11:0015
    
    Luis,
    
    	Did you put an entry into the HUBwatch Agents File for the
    DECserver 90TL? If you performed a [configuration][add] operation via
    HUBwatch and did not add an entry to the  HUBwatch Agents File, then
    the DECserver 90TL will show up on the Hub's Front Panel and will be
    accessible via HUBwatch until you exit HUBwatch. After that, when you
    enter HUBwatch, the  DECserver 90TL will show up on the Hub's Front
    Panel View, but will not be accessible via HUBwatch. You will get an 
    error that the agent does not respond. Make sure that the DECserver
    90TL has an entry in the HUBwatch Agents File. 
    
    Hope this helps,
    Bob