[Search for users] [Overall Top Noters] [List of all Conferences] [Download this site]

Conference netcad::hub_mgnt

Title:	DEChub/HUBwatch/PROBEwatch CONFERENCE
Notice:	Firmware -2, Doc -3, Power -4, HW kits -5, firm load -6&7
Moderator:	NETCAD::COLELLADT

Created:	Wed Nov 13 1991
Last Modified:	Fri Jun 06 1997
Last Successful Update:	Fri Jun 06 1997
Number of topics:	4455
Total number of notes:	16761

220.0. "HUBWATCH T1.1.18 BUG/CRASH" by CGOS01::DMARLOWE (dsk dsk dsk (tsk tsk tsk)) Thu Apr 29 1993 19:25

    I have found a HUBWATCH for VMS bug, with the help of a customer.
    
    This is for a double hub. 
    
    1    2    3    4    5    6    7    8    12    13
    90C  90C  90T  90T  90C  L+   Agen DB90 90T   90C
    
    Go to LOGICAL VIEW.  Only tried this on the 90Cs in slots 1 and
    2.  Normally it shows only 3 of the 6 ports and up/down arrows.
    Click so ports 4, 5 and 6 show.  Go to top of window and click on
    square to make window full screen.  It starts to redraw the hubs
    and repeaters.  The repeaters are drawn with 3 ports and then just
    before they are redrawn with 6 ports, HUBWATCH crashes with the
    following:
    
    %SYSTEM-F-ACCVIO, access violation, reason mask=00, virtual
    address=00000000, PC
    =0003A5A5, PSL=03C00004
    
      Improperly handled condition, image exit forced.
    
            Signal arguments              Stack contents
    
            Number = 00000005                200C0000
            Name   = 0000000C                7FF1CC54
                     00000000                00116F54
                     00000000                00000001
                     0003A5A5                00110190
                     03C00004                7FF1CC5A
                                             001134E4
                                             7FF1CC58
                                             001569CA
                                             003021F4
    
            Register dump
    
            R0 = 00000000  R1 = 00366198  R2 = 00000006  R3 = 00000003
            R4 = 007DA4B8  R5 = 0000009A  R6 = 009BF080  R7 = 7FF1CC0C
            R8 = 7FF1CC08  R9 = 003021F4  R10= 00000000  R11= 0030227E
            AP = 7FF1CBC4  FP = 7FF1CB84  SP = 7FF1CC00  PC = 0003A5A5
            PSL= 03C00004
     

    Running T1.1.18 of HUBWATCH.  Agent is V1.1 X1.77.
    
    Tried the same with the 90T in slot 3.  Clicked so ports 4,5 and
    6 show.  Still crashes.  Seems you must go to logical view first
    before you click on any of the up/down arrows.
    
    dave

T.R	Title	User	Personal Name	Date	Lines
220.1	Where's the bug spray?	CGOS01::DMARLOWE	dsk dsk dsk (tsk tsk tsk)	`Thu May 27 1993 14:57`	6
	Just a note (no pun intended). I just finished bringing up the SSB version (1.1) off the net and this bug still remains. dave
220.2	Release-noted for V1.1	SLINK::HOOD	I'd rather be surfing	`Thu May 27 1993 17:42`	2
	Yup. It's in the release notes. Make sure port 1 is showing before doing a resize.
220.3	will be fixed in 2.0	EMDS::SEAVER	Bill Seaver, HUBwatch Mktg	`Fri May 28 1993 11:14`	1
	Bruce Sweet promises it will be fixed in V2.0
220.4	No one told me that I had to read to get this job!	CGOS01::DMARLOWE	dsk dsk dsk (tsk tsk tsk)	`Fri May 28 1993 16:28`	5
	Got a mail message saying that stated in the release notes, that port 1 must show on all modules before resizing. Maybe I'll get enough time to read those notes. 8^) dave