Conference hydra::amiga_v1

    I had one but I lost them.
    I will look for them and will reply in this note again.
    
    'til tomorrow
    Gerald

    I have these as well but I dont know if they would be the same as
    yours. I am in Australia and we run 240 volts and PAL. If your problems
    dont lie in the power area you may be OK.
    
    Someone closer to you may be of more assistance, have you tried asking
    the Commodore tech support people for a copy?
    Failing that I can send you copies of these ones.
    
    Regards,
    John

    Ha, I've found mine again.
    
    These are:
    	schematic	ext.5� drive
    	   "		NTSC->PAL
    			RAM cartrige
    			motherboard
    			piggy back
    
    unfortunately these schematics are bad copies, so it makes no sense
    to copy them again.
    
    you can give me Your exact address (I live in Germany) to send them
    to You.
    
    BUT I want hem back, OK?
    
    Gerald

Last night I open my Amiga, after disconnecting all cables, I power up
and look for all events before the failure. 

On power up the Power LED blinks 5 times ,screen is dark for a minute or
so, and  I get the KS icon requester.
I load the KS into the floppy drive, the usual reading flows, next the 
monitor is dark, gray dark and dark again, no WB requester.
I did reset (A,A and CTRL) at this point, screen is going dark gray and
next dark .
As I was telling I have only the monitor attached to the A1000, Now, I read
note 2944 posted by Steve McAfee (the flake rep.), is my problem related
the Damage of the expansion port ?.
I had on this port 2MB MicroBotics, a Cltd., a 4000A, 30MegHD with its
power and cab. is possible that I overloaded Amiga power supply?.
I remember reading for a -12V. on the Amiga (on the video port) is this
supply by the Amiga power reg.?
As I said on my original note 3153 I did not see a -12v when I checked
voltages on the power sply. plug. Is this my problem?.
I would appreciate any help on this.!

Thanks.
Alex.

P.S. Dear Gerald I just read your reply, following is my address:
Alex. Dragomirescu
140 E., 7th.St., Ap.2-O.
New York, NY, Zip.10009
Ill copy and send them back, promise!!(EUROPA is going trough big time
lately, is coming back to life again, my hard is with you, and people
in my homeland (Romania)!!.)
                            

    You should still be able to buy the Amiga 1000 Hardware Technical
    Manual (or similar title) from Commodore-Amiga Technical Support in
    West Chester, PA.  Cost is about $25.  This includes a complete
    schematic, PAL equations and explanations of the old Zorro I expansion
    bus and autoconfig.  I believe there's an old note describing documents
    available from CATS somewhere early in this notesfile.
    
    Don't confuse this manual with the _Amiga Hardware Manual_ published
    by Addison-Wesley.  The latter is really a programmer's manual and
    includes no schematics.
    
    Wes

    CATS - orders,
    Software Administration,
    CBM,
    1200, Wilson Drive,
    West Chester, PA 19380.
    (215)431-9180.

    or try

    Cardinal Software,
    14840, Build America Drive,
    Woodbridge, VA 22191.
    (703)491-6494.

    I bought mine from Cardinal.  They are hugh (24" x 36").  You should
    try to get it from one of the above two places first.  If that failed,
    send me mail and we can figure out something.

    Chong.

	Hello Alex,

I do not have an A1000 to be able to help you much but I wonder if there is
no hardware test disk at Commodore as the A1000 relies on KS loading.
They should have this disk to load instead of the KS for hardware diagnosis.
If I obtain any information from a friend who had an A1000 I'll pass it to
you.

Best regards,
Sorin

P.S. Yes, there are good things happening in Europe but Romania (which is
also my homeland) remains stone cold unfortunately.

Many thanks to  all of you who reply to my first two req. on note 3153 $
3160.
 I called CBM at 215-4364200 (Com. Cust. Supp.), after 35-40 min. on hold
they offer me a Service Manual for 55$ + 3$ shipping, # 314038-02.
 I am going for it, the only think is that is going to take 3 to 4 Weeks
to get it. Well, I have to wait, and look to my A1000 for all this time.

 (Sorin, you are right "BLOODED stone cold"!, but I have hopes for a
" HOT spring " coming.!, . Keep in touch!?)

Alex.
                                 

    Ref. .8
    
    Hello again Alex,
    
    Sure I'll like to keep in touch !
    I'll send you a mail.
    
    Best regards,
    Sorin