| Well, I got the installation guide for the internal kit, and read
it.
Some things aren't yet clear for me.
1 - The IG says: the LN01 fonts must be ordered separately but if you
have them from a T1.0 system, you do not need to reinstall them.
2 - On a T1.0 system, the directory DOC$LN01_FONTS is identical
to the one on the V1.0 system I just generated from scratch (installed
the DOC010, DOCLN03010, DOCINT010 kits, in this sequence, with no
other version of DOCUMENT already on the system).
3 - On this system however, the compilation of an LN01 book failed
(see log below). It ran ok for the LN03 format.
The questions are:
1 - Did the book compilation really failed because the LN01 fonts were
missing ?
2 - If yes, is there a way to install them from my T1.0 system,
or shall I still send a mail to CLOSET::LN01FONTS to get them ?
Thanks a lot for helping, and sorry if my questions sound naives
:-))
Marc
[ T e x t F o r m a t t i n g ]...
%TEX-I-IDENT, V1.0
%TEX-I-INFO, The LN01 does not support inclusion of DVI files. - on page [iv]
%TEX-I-LINETOOSHORT, Line too short - on page [3-4]
%TEX-I-LINETOOSHORT, Line too short - on page [4-4]
%TEX-I-LINETOOSHORT, Line too short - on page [8-2]
%TEX-I-LINETOOSHORT, Line too short - on page [8-9]
%TEX-I-LINETOOSHORT, Line too short - on page [8-11]
%TEX-I-LINETOOSHORT, Line too short - on page [8-12]
%TEX-I-LINETOOSHORT, Line too short - on page [8-13]
%TEX-I-LINETOOSHORT, Line too short - on page [8-13]
%TEX-I-LINETOOSHORT, Line too short - on page [14-2]
%TEX-I-LINETOOSHORT, Line too short - on page [17-2]
%TEX-I-LINETOOSHORT, Line too short - on page [D-1]
%TEX-I-LINETOOSHORT, Line too short - on page [D-1]
%TEX-I-PAGESOUT, 94 pages written.
-TEX-I-OUTFILENAME, 'login$disk:[buresi.tmp]ISA1PRO.DVI_LN01'
[ C o n t e n t s G e n e r a t i o n ]...
[ T e x t F o r m a t t i n g C o n t e n t s ]...
%TEX-I-IDENT, V1.0
%TEX-I-PAGESOUT, 12 pages written.
-TEX-I-OUTFILENAME, 'login$disk:[buresi.tmp]ISA1PRO_CONTENTS.DVI_LN01'
[ D e v i c e C o n v e r s i o n ]...
$ ! DVC$LN01.COM for DOCUMENT T1.0 (Internal Use Only)
This is DVItype, Version 2.6, with LN03 Version 0.92
%SYSTEM-F-ACCVIO, access violation, reason mask=05, virtual address=7FEFAFF8, PC=0000B74A, PSL=03C000A0
Improperly handled condition, image exit forced.
Signal arguments Stack contents
%SYSTEM-F-RADRMOD, reserved addressing fault at PC=7FF512CA, PSL=03C00020
Improperly handled condition, image exit forced.
Signal arguments Stack contents
Number = 00000003 00000000
Name = 0000044C 04010000
7FF512CA 7FF5156C
03C00020 7FF51530
80000014
7FF5115D
7FF514EC
80017E92
00000002
7FF513F0
Register dump
R0 = 7FF5115D R1 = 7FF512C8 R2 = 000000FC R3 = 7FF514EC
R4 = 00000000 R5 = 00000004 R6 = 7FF515EC R7 = 7FF5146D
R8 = 7FF51600 R9 = 7FF51454 R10= 7FF514EC R11= 7FF514A8
AP = 7FF51378 FP = 7FF51338 SP = 7FF513AC PC = 7FF512CA
PSL= 03C00020
%PLI-S-FINISH, PL/I Program FINISH condition.
$ exit ($status + (0 * f$verify(verify_context))) ! SYS$SCRATCH:DOC$ISA1PRO.TMP - End
BURESI job terminated at 11-AUG-1987 18:04:48.11
Accounting information:
Buffered I/O count: 1079 Peak working set size: 3647
Direct I/O count: 1950 Peak page file size: 8633
Page faults: 4310 Mounted volumes: 0
Charged CPU time: 0 00:44:20.97 Elapsed time: 0 01:48:41.20
|