Conference share::zap

109.0. "Warning Message before it zapped" by HGOVC::BARRYHO () Wed Mar 25 1992 23:26

I have installed ZAP V4.2 with VMS T5.5-1E7.  Please see the attached
files ZAP.DAT, ZAP.MSG and ZAP.LOG for more information.  

1. No warning message was found before the session logged out by ZAP.
   I expect a boardcast warning message will display on the inactive 
   terminal in the last 3 and 1 minute before they are terimated.  
   Only the following line was found on the terminal before it zapped:
   "[Zap: LTA5217:BARRYHO logged out at 11:46:46.71 after 4 min idle time".
   The UIC of BARRYHO is [500,1].   

2. The above message was found in a LAT session.  But when I use set host
   session (RTA2), I can not found the message before it zapped.

3. Is there any ZAP presentation material available?
  

Thanks in advance.
barry


ZAP.DAT
----------------------------------------------------------------------------
/sensitivity=5
/traceback=true
/debug=false
/send=9,7,5,3,1
/inswap=false
/ignore_suspended=false
/image=mail /com=zap$stop_mail
[*,*]		*		console		*		nomessage
[001,004]	*		remote		4		message
[001,*]		*		all		*		nomessage
[*,*]		*		batch		*		nomessage
[*,*]		*		network		*		nomessage
[*,*]		*		detach		*		nomessage
[*,*]		*		all		4		message


ZAP.MSG
----------------------------------------------------------------------------
%bZap idle process status at %t

 Device: %d

 Username: %u

 Minutes of idle time accumulated: %a

 Minutes of idle time remaining:   %r


ZAP.LOG
---------------------------------------------------------------------------
$!
$! This command procedure is always run when anybody on the entire system
$! logs in. It is equivalent to LOGIN.COM except that the instructions
$! contained herein are executed everytime anyone on the VMS system
$! logs in to their account.
$!
$! For interactive processes, turn on Control T, and set the terminal type
$!
$ IF (F$MODE() .EQS. "INTERACTIVE") THEN SET CONTROL=T
$ IF (F$MODE() .EQS. "INTERACTIVE") THEN SET TERMINAL/INQUIRE
$!
$! For MicroVAX systems only, use the command MOUNT/NOASSIST.
$!
$ IF (.NOT. F$TRNLNM("SYS$MICROVAX")) THEN GOTO SKIP_MICROVAX_COMMANDS
$SKIP_MICROVAX_COMMANDS:
$!
$! Place your site-specific LOGIN commands below
$!
$
$ !	This procedure is executed in a detached process via LOGINOUT.EXE
$ !	so that Zap will run with a CLI.  This is done so that it may
$ !	create sub-processes to log out users with user written DCL command
$ !	procedures.
$
$	Define/job/exec sys$login SYS$SYSROOT:[ZAP]
$	Define/job/exec sys$login_device SYS$SYSROOT:
$	Define/job/exec sys$scratch SYS$SYSROOT:[ZAP]
$
$	Show logical/process

(LNM$PROCESS_TABLE)

  "SYS$COMMAND" = "_$1$DKA100:"
  "SYS$DISK" = "SYS$SYSROOT:"
  "SYS$ERROR" = "_$1$DKA100:"
  "SYS$INPUT" = "_$1$DKA100:"
  "SYS$OUTPUT" [super] = "_$1$DKA100:"
  "SYS$OUTPUT" [exec] = "_$1$DKA100:"
  "TT" = "ZAP$DIR:ZAP.COM"
$	Show logical/job

(LNM$JOB_8078A370)

  "SYS$LOGIN" = "SYS$SYSROOT:[ZAP]"
  "SYS$LOGIN_DEVICE" = "SYS$SYSROOT:"
  "SYS$SCRATCH" = "SYS$SYSROOT:[ZAP]"
$
$	Run Zap$Dir:Zap
[Zap: Idle process deletion utility, Version 4.2]
[Zap: Starting at 25-MAR-1992 11:41:46.25]
[Zap: reading exception file (zap$dir:zap.dat) at 25-MAR-1992 11:41:46.35]
[Zap: Image exception record read for MAIL                                   ]
[Zap: Idle sensitivity set to 5]
[Zap: Process traceback has been set to   TRUE]
[Zap: Image debug has been set to  FALSE]
[Zap: Warning messages send times set to 9,7,5,3,1]
[Zap: Process inswap has been set to  FALSE]
[Zap: Ignore suspended has been set to   TRUE]
[Zap: reading warning message file (zap$dir:zap.msg) at 25-MAR-1992 11:41:46.52]
[Zap: Warning message is 186 characters long]
[Zap: USERNAME change: Process _RTA2: from <login> to BARRYHO]
[Zap: RTA1:   ABBOTTCHEUNG logged out at 11:45:46.71 after 4 min idle time]
[Zap: LTA5217:BARRYHO logged out at 11:46:46.71 after 4 min idle time]
[Zap: RTA2:   BARRYHO logged out at 11:49:46.71 after 4 min idle time]
[Zap: Exiting at 25-MAR-1992 11:52:46.54]
[Zap: Final pass count = 11]
[Zap: Final stopped count = 3]
[Zap: Final error count = 0]
$
  SYSTEM       job terminated at 25-MAR-1992 11:52:46.71

  Accounting information:
  Buffered I/O count:              46         Peak working set size:     376
  Direct I/O count:                23         Peak page file size:      3337
  Page faults:                    513         Mounted volumes:             0
  Charged CPU time:           0 00:00:02.75   Elapsed time:     0 00:11:01.99
-------------------------------------------------------------------------------

				*** END ***	
 

ZAP V4.2 has not been tested on VMS T5.5-1E7, but it does work on V5.5.
Could you please re-install the kit and see if this corrects the problem.