[Search for users]
[Overall Top Noters]
[List of all Conferences]
[Download this site]
| Title: | CSGUK_SYSTEMS |
| Notice: | No restrictions on keyword creation |
| Moderator: | KERNEL::ADAMS |
|
| Created: | Wed Mar 01 1989 |
| Last Modified: | Thu Nov 28 1996 |
| Last Successful Update: | Fri Jun 06 1997 |
| Number of topics: | 242 |
| Total number of notes: | 1855 |
29.0. "scorpio goodies" by KERNEL::ADAMS (Venus on Remote Control) Thu Apr 20 1989 02:48
Good morning,
Please take note,I'll spell this word perfect for Dave Clark,although it
doesn't apply to all of devices,mostly those on shift.
Further to a mail yesterday regarding EPROM updates on Scorpio machines,
an attempt to update the patch revision levels remotely was sucessfully
achieved.The session is below.The FCO quoted yesterday,which also appears
on Stars,upgrades microcode on the Scorpio to rev 21,min required for VMS
V5.0.
This update to rev 25,allowed the customer to run SMP (synchronous multy
processing) on his 8350 machines,which previously had a mis-match,with rev
25 on the primary cpu & 23 on secondary.This could also occur in future if an
engineer swaps the cpu module,without checking the rev levels,with V5.0
installed.
It is a bit long winded, but there were 2 machines upgraded,the second
experiencing chksum errs until reseated.This procedure could save the
branch/customer several wasted hours.Only 2 floppies required,diagnostic
supervisor & floppy with ebuca diagnostic.
Thanks to Ken Robb for his assistance.
PS.Any feedback,greatly appreciated,sarcasm excluded,Richard.
-----------------------------------------------------------------------------
Log for call ID R9126475C created 7-SEP-1988 13:41:23.49.
MOUNTFORD Connected at 7-SEP-1988 13:41:22.49
System id :CLUK03073 Cpu type :CLUST Console :MDS01
Speed :1200 Keyboard :TTB0 Phone :6260660
*******************************************************************
*** Connection Established by RDC Basingstoke. ***
*******************************************************************
Message "RSDS$MGR:RSDSMSG.EN" sent successfully.
Entering TRANS mode [protocol off] (^A to exit)...
?02
PC = 8018F166
>>>^P
>>>H
PC = 8018F166
>>>B CSA1
. . 2 . . 5 6 7 8 . . . . . . F
02000000Z
VAX DIAGNOSTIC SOFTWARE
PROPERTY OF
DIGITAL EQUIPMENT CORPORATION
***CONFIDENTIAL AND PROPRIETARY***
Use Authorized Only Pursuant to a Valid Right-to-Use License
Copyright, Digital Equipment Corporation, 1987. All Rights Reserved.
DIAGNOSTIC SUPERVISOR. ZZ-EBSAA-10.9-885 8-SEP-1987 13:52:28
DS> SET QU
DS> R EVSBA/SEC:SE
DS> DIR
Directory CSA1:[SYSMAINT]
EBSAA.EXE;1 EVSAA.HLP;139 FG79.VG0;1 V109RELNOT.MEM;4
Total of 4 files.
DS> DIR
Directory CSA1:[SYSMAINT]
CSBOOKA.SYS;2 DUBOOKA.SYS;17 EBSAA.EXE;1 EBUCA.COM;3
EBUCA.EXE;13 EBUCA.HLP;19 EEPROM.IMA;1 ETBOOKA.SYS;11
FG80.VI0;1 KA0023.PAT;13 KA021B.PAT;2 KA825.SYS;1
KA8BOO.SYS;1 KA8BOO2.SYS;1 KAINIT.SYS;6 KAINIT2.SYS;1
MUBOOKA.SYS;14
Total of 17 files.
DS> SET VER
DS> @EBUCA
DS> LOAD EBUCA
DS> ATTACH KA820 HUB KA0 2048 0
DS> SEL KA0
DS> SET MM OFF
DS> START
.. Program: EBUCA-VAX 8200/8300 EEPROM UTILITY and VAXBI CONFIGURATOR, revision
2.4, 1 test,
at 13:56:37.14.
Testing: _KA0
** EBUCA STARTUP **
Do you want help Y/N {N} ? N
Source for loading EEPROM work buffer is the primary processor
Want to change this Y/N {N} ?
^C
DS> ATT KA83\3\20 HUB
Device Name? KA1
K-bytes of Main Memory? 0
BI Node Number (HEX)? 6
DS> SH SE\ES HS\SEL ALL
DS> SH DEV
_CSA1 console HUB 00000000
_CSA2 console HUB 00000000
_KA0 KA820 HUB 00000000 K-bytes of Main Memory=2048. BI Node Number (H
EX)=00000000(X)
_KA1 KA820 HUB 00000000 K-bytes of Main Memory=0. BI Node Number (HEX)
=00000006(X)
DS> @EBUCA
DS> LOAD EBUCA
DS> ATTACH KA820 HUB KA0 2048 0
DS> SEL KA0
DS> SET MM OFF
DS> START
.. Program: EBUCA-VAX 8200/8300 EEPROM UTILITY and VAXBI CONFIGURATOR, revision
2.4, 1 test,
at 13:58:52.56.
Testing: _KA1
** EBUCA STARTUP **
Do you want help Y/N {N} ? @ <EOF>
Do you want help Y/N {N} ?
Source for loading EEPROM work buffer is the primary processor
Want to change this Y/N {N} ?
EE> Are you interested in the general section Y/N {N} ? Y
Want to display VAXBI configuration matrix Y/N {N} ? Y
_____________________________________________________________
NODE REVISION CODE DEVICE CODE & TYPE
_____________________________________________________________
02 9033 0105 KA825 CPU
05 0247 410F DEBNT
06 902F 0105 KA825 CPU
07 0003 0001 MS820 MEMORY
08 4301 0108 CIBCA
0F 0003 0001 MS820 MEMORY
Want to display a summary of EEPROM contents (From Work Buffer) Y/N {N} ? N
CPU serial number is GA81182946
Want to change this Y/N {N} ? N
RCX50 selftest is enabled
Want to change this Y/N {N} ? N
VAXBI selftest timeout in seconds is 25
Want to change this Y/N {N} ?
FCHIP is enabled
Want to change this Y/N {N} ?
CACHE is enabled
Want to change this Y/N {N} ?
- - END OF SECTION - WANT TO REPEAT IT Y/N {N} ? Y
EE> Are you interested in the general section Y/N {N} ? Y
Want to display VAXBI configuration matrix Y/N {N} ? Y
_____________________________________________________________
NODE REVISION CODE DEVICE CODE & TYPE
_____________________________________________________________
02 9033 0105 KA825 CPU
05 0247 410F DEBNT
06 902F 0105 KA825 CPU
07 0003 0001 MS820 MEMORY
08 4301 0108 CIBCA
0F 0003 0001 MS820 MEMORY
Want to display a summary of EEPROM contents (From Work Buffer) Y/N {N} ? N
CPU serial number is GA81182946
Want to change this Y/N {N} ? N
RCX50 selftest is enabled
Want to change this Y/N {N} ? Y
VAXBI selftest timeout in seconds is 25
Want to change this Y/N {N} ?
FCHIP is enabled
Want to change this Y/N {N} ?
CACHE is enabled
Want to change this Y/N {N} ?
- - END OF SECTION - WANT TO REPEAT IT Y/N {N} ? N
EE> Are you interested in the console section Y/N {N} ?
EE> Are you interested in the boot code section Y/N {N} ?
EE> Are you interested in the microcode patch section Y/N {N} ? Y
Want to examine/modify CPU and Patch revision information Y/N {N} ? Y
CPU REV: 18
Want to change this Y/N {N} ?
PATCH REV: 25
Want to change this Y/N {N} ?
Want to compare patches in buffer against patch file on disk Y/N {N} ?
Want to load a new set of microcode patches Y/N {N} ?
Want to list patches (From buffer) Y/N {N} ?
Want to add a single microcode patch Y/N {N} ?
Want to remove a single microcode patch Y/N {N} ?
- - END OF SECTION - WANT TO REPEAT IT Y/N {N} ? N
EE> Are you interested in examine/deposit section Y/N {N} ?
EE> Are you interested in the Ethernet section Y/N {N} ?
* END OF PASS *
Want to make another pass Y/N {N} ?
Want to abort this session Y/N {N} ? N
Want to write buffer to image file EEPROM.IMA on CSA1 Y/N {N} ? Y
%%ERROR writing or reading EEPROM image file
Diskette in CSA1 must contain image file EEPROM.IMA
Verify that media is not write protected
Want to write buffer to image file EEPROM.IMA on CSA1 Y/N {N} ? N
Want to write changes back to the same EEPROM Y/N {N} ?
Want to select destination node for outputing changes Y/N {N} ? Y
NODE NUMBER CPU PROCESOR TYPE
_____________________________________________________________
02 CPU-PRIMARY 2 EEPROM'S
06 CPU-ATTACHED 2 EEPROM'S
Enter destination node number in Hex: {02} : 06
Update could take several minutes-DO NOT ABORT DURING UPDATE
** Operation was SUCCESSFUL **
Want to exit the utility Y/N {N} ? N
**NO MORE CHOICES**
Want to make another pass Y/N {N} ? Y
EE> Are you interested in the general section Y/N {N} ?
^C
DS> ST
.. Program: EBUCA-VAX 8200/8300 EEPROM UTILITY and VAXBI CONFIGURATOR, revision
2.4, 1 test,
at 14:04:02.80.
Testing: _KA1
** EBUCA STARTUP **
Do you want help Y/N {N} ? N
Source for loading EEPROM work buffer is the primary processor
Want to change this Y/N {N} ?
EE> Are you interested in the general section Y/N {N} ?
^C
DS> ST
.. Program: EBUCA-VAX 8200/8300 EEPROM UTILITY and VAXBI CONFIGURATOR, revision
2.4, 1 test,
at 14:04:19.78.
Testing: _KA1
** EBUCA STARTUP **
Do you want help Y/N {N} ?
Source for loading EEPROM work buffer is the primary processor
Want to change this Y/N {N} ? Y
Want to load buffer from initialization file KAINITx.SYS Y/N {N} ?
Want to load buffer from EEPROM saved image on CSA1 Y/N {N} ?
Want to load buffer from EEPROM of an attached processor Y/N {N} ? Y
NODE NUMBER CPU PROCESOR TYPE
_____________________________________________________________
02 CPU-PRIMARY 2 EEPROM'S
06 CPU-ATTACHED 2 EEPROM'S
Enter source node number in Hex: {02} : 06
EE> Are you interested in the general section Y/N {N} ?
EE> Are you interested in the console section Y/N {N} ?
EE> Are you interested in the boot code section Y/N {N} ?
EE> Are you interested in the microcode patch section Y/N {N} ? Y
Want to examine/modify CPU and Patch revision information Y/N {N} ? Y
CPU REV: 18
Want to change this Y/N {N} ?
PATCH REV: 25
Want to change this Y/N {N} ?
Want to compare patches in buffer against patch file on disk Y/N {N} ?
Want to load a new set of microcode patches Y/N {N} ?
Want to list patches (From buffer) Y/N {N} ?
Want to add a single microcode patch Y/N {N} ?
Want to remove a single microcode patch Y/N {N} ?
- - END OF SECTION - WANT TO REPEAT IT Y/N {N} ? N
EE> Are you interested in examine/deposit section Y/N {N} ? N
EE> Are you interested in the Ethernet section Y/N {N} ? N
* END OF PASS *
Want to make another pass Y/N {N} ? Y\Y\N
Want to abort this session Y/N {N} ? N
Want to write buffer to image file EEPROM.IMA on CSA1 Y/N {N} ? Y
** Operation was SUCCESSFUL **
Want to exit the utility Y/N {N} ? Y
.. End of run, 0 errors detected, pass count is 1,
time is 8-SEP-1987 14:08:37.16
DS>
?02
PC = 00022AA0
>>>H
PC = 00022AA0
>>>B
. . 2 . . 5
#�
#ABCDEFGHIJK.MN#
. . 2 . . 5 6 7 8 . . . . . . F
02000000
D/G 0 20! CODE FOR CI ADAPTER
D/G 1 8! NODE NUMBER ON BACKPLANE FOR CI
D/G 2 0100! HSC50 NODE NUMBERS
D/G 3 0! DISK DRIVE NUMBER
D/G 5 0! S/W BOOT FLAGS
D/G E 200
LOAD VMB.EXE/START:200
START 200! GO FOR IT...........
VAX/VMS Version V5.0-1 Major version id = 1 Minor version id = 0
%CNXMAN, Using remote access method for quorum disk
%SMP-I-CPUBOOTED, CPU #06 has joined the PRIMARY CPU in multiprocessor operation
waiting to form or join a VAXcluster system
%CNXMAN, Using local access method for quorum disk
%CNXMAN, Established "connection" to quorum disk
%CNXMAN, Proposing formation of a VAXcluster
%CNXMAN, Now a VAXcluster member -- system N1
%CNXMAN, Quorum lost, blocking activity
%CNXMAN, Completing VAXcluster state transition
%CNXMAN, Quorum regained, resuming activity
$! Copyright (c) 1988 Digital Equipment Corporation. All rights reserved.
%%%%%%%%%%% OPCOM 7-SEP-1988 14:16:47.26 %%%%%%%%%%%
Logfile has been initialized by operator _N1$OPA0:
Logfile is SYS$SYSROOT:[SYSMGR]OPERATOR.LOG;7
%%%%%%%%%%% OPCOM 7-SEP-1988 14:16:47.94 %%%%%%%%%%%
09:54:51.53 Node N1 (csid 00000000) is using remote access method for quorum disk
%%%%%%%%%%% OPCOM 7-SEP-1988 14:16:47.97 %%%%%%%%%%%
14:13:06.74 Node N1 (csid 00000000) is using local access method for quorum disk
%%%%%%%%%%% OPCOM 7-SEP-1988 14:16:48.05 %%%%%%%%%%%
14:13:06.78 Node N1 (csid 00000000) re-established "connection" to quorum disk
%%%%%%%%%%% OPCOM 7-SEP-1988 14:16:48.12 %%%%%%%%%%%
14:14:19.74 Node N1 (csid 00000000) proposed formation of a VAXcluster
%%%%%%%%%%% OPCOM 7-SEP-1988 14:16:48.18 %%%%%%%%%%%
14:14:19.74 Node N1 (csid 00010001) is now a VAXcluster member
%LICENSE-I-LOADED, DEC DVNETRTG was successfully loaded with 0 units
%%%%%%%%%%% OPCOM 7-SEP-1988 14:16:48.23 %%%%%%%%%%%
14:14:19.76 Node N1 (csid 00010001) lost quorum, blocking activity
%%%%%%%%%%% OPCOM 7-SEP-1988 14:16:48.26 %%%%%%%%%%%
14:14:19.76 Node N1 (csid 00010001) completed VAXcluster state transition
%%%%%%%%%%% OPCOM 7-SEP-1988 14:16:48.29 %%%%%%%%%%%
14:15:47.75 Node N1 (csid 00010001) regained quorum, proceeding
%LICENSE-I-LOADED, DEC VAXCLUSTER was successfully loaded with 0 units
%SYSTEM-W-ALLSTARTED, all configured processors are already started
%MOUNT-I-MOUNTED, DATA mounted on _HSC001$DUA1:
%MOUNT-I-MOUNTED, SHADOW mounted on _HSC001$DUA2:
%MOUNT-I-MOUNTED, DEVELOPMENT mounted on _HSC001$DUA3:
%MOUNT-I-REBUILD, volume was improperly dismounted; rebuild in progress
%RUN-S-PROC_ID, identification of created process is 2020008D
%%%%%%%%%%% OPCOM 7-SEP-1988 14:18:08.82 %%%%%%%%%%%
Message from user DECNET on N1
DECnet starting
%NCP-I-NOINFO, No information in database
%NCP-I-NOINFO, No information in database
%DCL-I-SUPERSEDE, previous value of MOM$LOAD has been superseded
%%%%%%%%%%% OPCOM 7-SEP-1988 14:18:17.60 %%%%%%%%%%%
Message from user DECNET on N1
DECnet event 4.10, circuit up
From node 1.3 (N1), 7-SEP-1988 14:18:17.40
Circuit BNA-0
%NCP-I-NOINFO, No information in database
%RUN-S-PROC_ID, identification of created process is 2020008F
LCP Characteristics
Node name = \N1\
Node Identification = \SYS$ANNOUNCE\
Groups = (0)
Multicast timer = 60 seconds
LAT Version = 5.1 LAT Protocol is inactive
Service Names and Ids:
Service name : \N1\ rating : <auto>
ID : \VAX Cluster\
LCP Characteristics
Node name = \N1\
Node Identification = \SYS$ANNOUNCE\
Groups = (0)
Multicast timer = 60 seconds
LAT Version = 5.1 LAT Protocol is active
Service Names and Ids:
Service name : \N1\ rating : <auto>
ID : \VAX Cluster\
Node Links:
Link name = \LAT$LINK\
Link device = \ETA0:\
Groups = ()
Link-specific services:
Status = Active
%LAT-I-STARTED, LAT terminal port driver started
%SET-I-INTSET, login interactive limit = 64, current interactive value = 0
7-SEP-1988 14:18:53
SYSTEM job terminated at 7-SEP-1988 14:18:57.10
Accounting information:
Buffered I/O count: 1357 Peak working set size: 805
Direct I/O count: 1314 Peak page file size: 3248
Page faults: 11153 Mounted volumes: 3
Charged CPU time: 0 00:01:33.36 Elapsed time: 0 00:02:58.71
Username:
Error reading command input
Timeout period expired
Username: FIELD
Password:
User authorization failure
Username:
Exiting TRANS mode [protocol on]...
REM> DISC
MOUNTFORD disconnected at 7-SEP-1988 14:20:32.02
MOUNTFORD Connected at 7-SEP-1988 14:22:10.45
System id :CLUK03073 Cpu type :CLUST Console :MDS01
Speed :1200 Keyboard :TTC6 Phone :6260660
*******************************************************************
*** Connection Established by RDC Basingstoke. ***
*******************************************************************
Message "RSDS$MGR:RSDSMSG.EN" sent successfully.
REM>
REM>
REM> TR
Entering TRANS mode [protocol off] (^A to exit)...
>>>H
PC = 801BD566
>>>B CSA1~r
. . 2 . . 5 6 7 8 . . B C D E F
06000000
?44
?06
PC = 20090201
?42
PC = 20090201
>>>B CSA1
. . 2 . . 5 6 7 8 . . B C D E F
06000000Z
VAX DIAGNOSTIC SOFTWARE
PROPERTY OF
DIGITAL EQUIPMENT CORPORATION
***CONFIDENTIAL AND PROPRIETARY***
Use Authorized Only Pursuant to a Valid Right-to-Use License
Copyright, Digital Equipment Corporation, 1987. All Rights Reserved.
DIAGNOSTIC SUPERVISOR. ZZ-EBSAA-10.9-885 8-SEP-1987 14:25:49
DS> R\R\
DS> ATT KA820 HUB KA1
K-bytes of Main Memory? 0
BI Node Number (HEX)? 6
DS> @EBUCA
.. Program: EBUCA-VAX 8200/8300 EEPROM UTILITY and VAXBI CONFIGURATOR, revision
2.4, 1 test,
at 14:27:43.69.
Testing: _KA0
** EBUCA STARTUP **
Do you want help Y/N {N} ?
^C
DS> SEL ALL
DS> SH DEV
_CSA1 console HUB 00000000
_CSA2 console HUB 00000000
_KA1 KA820 HUB 00000000 K-bytes of Main Memory=0. BI Node Number (HEX)
=00000006(X)
_KA0 KA820 HUB 00000000 K-bytes of Main Memory=2048. BI Node Number (H
EX)=00000000(X)
DS> ST
.. Program: EBUCA-VAX 8200/8300 EEPROM UTILITY and VAXBI CONFIGURATOR, revision
2.4, 1 test,
at 14:28:24.14.
Testing: _KA1
** EBUCA STARTUP **
Do you want help Y/N {N} ? N
Source for loading EEPROM work buffer is the primary processor
Want to change this Y/N {N} ?
EE> Are you interested in the general section Y/N {N} ?
EE> Are you interested in the console section Y/N {N} ?
EE> Are you interested in the boot code section Y/N {N} ?
EE> Are you interested in the microcode patch section Y/N {N} ?
^C
DS> ST
.. Program: EBUCA-VAX 8200/8300 EEPROM UTILITY and VAXBI CONFIGURATOR, revision
2.4, 1 test,
at 14:29:02.14.
Testing: _KA1
** EBUCA STARTUP **
Do you want help Y/N {N} ?
Source for loading EEPROM work buffer is the primary processor
Want to change this Y/N {N} ?
EE> Are you interested in the general section Y/N {N} ?
EE> Are you interested in the console section Y/N {N} ? Y
Console default BAUD rate is 1200
Want to change this Y/N {N} ?
The VAXBI node number of the logical console is 02
Want to change this Y/N {N} ?
- - END OF SECTION - WANT TO REPEAT IT Y/N {N} ?
EE> Are you interested in the boot code section Y/N {N} ? Y
Want to display boot summary Y/N {N} ?
The default boot device is CSA1
Want a different default boot device type Y/N {N} ?
The default boot device is CSA1
Want to modify the default boot device node and unit number Y/N {N} ?
Want to verify bootcode against files on disk Y/N {N} ?
Want to display bootcode files in HEX (from work buffer) Y/N {N} ?
Want to remove any boot code from the buffer Y/N {N} ?
Want to replace the Boot Command Parser Y/N {N} ?
Want to add bootcode for another boot device type Y/N {N} ?
Lo 13 bits of the DU boot device controller IP address in hex is 1468
Want to change this Y/N {N} ?
- - END OF SECTION - WANT TO REPEAT IT Y/N {N} ?
EE> Are you interested in the microcode patch section Y/N {N} ? Y
Want to examine/modify CPU and Patch revision information Y/N {N} ? Y
CPU REV: 18
Want to change this Y/N {N} ?
PATCH REV: 23
Want to change this Y/N {N} ?
Want to compare patches in buffer against patch file on disk Y/N {N} ?
Want to load a new set of microcode patches Y/N {N} ?
Want to list patches (From buffer) Y/N {N} ?
Want to add a single microcode patch Y/N {N} ?
Want to remove a single microcode patch Y/N {N} ?
- - END OF SECTION - WANT TO REPEAT IT Y/N {N} ? Y
EE> Are you interested in the microcode patch section Y/N {N} ?
EE> Are you interested in examine/deposit section Y/N {N} ?
EE> Are you interested in the Ethernet section Y/N {N} ?
* END OF PASS *
Want to make another pass Y/N {N} ? Y
EE> Are you interested in the general section Y/N {N} ? Y
Want to display VAXBI configuration matrix Y/N {N} ? Y
_____________________________________________________________
NODE REVISION CODE DEVICE CODE & TYPE
_____________________________________________________________
02 902F 0105 KA825 CPU
05 0247 410F DEBNT
06 902F 0105 KA825 CPU
07 0003 0001 MS820 MEMORY
08 4301 0108 CIBCA
0B 0003 0001 MS820 MEMORY
0C 0003 0001 MS820 MEMORY
0D 0003 0001 MS820 MEMORY
0E 0003 0001 MS820 MEMORY
0F 0003 0001 MS820 MEMORY
Want to display a summary of EEPROM contents (From Work Buffer) Y/N {N} ?
CPU serial number is NI00000000
Want to change this Y/N {N} ?
RCX50 selftest is enabled
Want to change this Y/N {N} ?
VAXBI selftest timeout in seconds is 25
Want to change this Y/N {N} ?
FCHIP is enabled
Want to change this Y/N {N} ?
CACHE is enabled
Want to change this Y/N {N} ?
- - END OF SECTION - WANT TO REPEAT IT Y/N {N} ?
EE> Are you interested in the console section Y/N {N} ? Y
Console default BAUD rate is 1200
Want to change this Y/N {N} ?
The VAXBI node number of the logical console is 02
Want to change this Y/N {N} ?
- - END OF SECTION - WANT TO REPEAT IT Y/N {N} ?
^C
DS> SY\Y\T
.. Program: EBUCA-VAX 8200/8300 EEPROM UTILITY and VAXBI CONFIGURATOR, revision
2.4, 1 test,
at 14:33:20.18.
Testing: _KA1
** EBUCA STARTUP **
Do you want help Y/N {N} ?
Source for loading EEPROM work buffer is the primary processor
Want to change this Y/N {N} ? Y
Want to load buffer from initialization file KAINITx.SYS Y/N {N} ?
Want to load buffer from EEPROM saved image on CSA1 Y/N {N} ? Y
EE> Are you interested in the general section Y/N {N} ? Y
Want to display VAXBI configuration matrix Y/N {N} ?
Want to display a summary of EEPROM contents (From Work Buffer) Y/N {N} ?
CPU serial number is GA81182946
Want to change this Y/N {N} ? 0\0\Y
Enter full 10 character serial number: {GA81182946} : 0000000000
%%ERROR - Invalid response
CPU Serial number is of the form PPYWWSSSSS
Where PP is the 2 character plant code (NI, GA or SG) Y, WW
and SSSSS are numeric values for year, week and serial number
CPU serial number is GA81182946
Want to change this Y/N {N} ? NI0000000\0000000IN\Y
Enter full 10 character serial number: {GA81182946} : NI00000000
RCX50 selftest is disabled
Want to change this Y/N {N} ? Y
VAXBI selftest timeout in seconds is 25
Want to change this Y/N {N} ?
FCHIP is enabled
Want to change this Y/N {N} ?
CACHE is enabled
Want to change this Y/N {N} ?
- - END OF SECTION - WANT TO REPEAT IT Y/N {N} ?
EE> Are you interested in the console section Y/N {N} ? Y
Console default BAUD rate is 1200
Want to change this Y/N {N} ?
The VAXBI node number of the logical console is 02
Want to change this Y/N {N} ?
- - END OF SECTION - WANT TO REPEAT IT Y/N {N} ?
EE> Are you interested in the boot code section Y/N {N} ? Y
Want to display boot summary Y/N {N} ?
The default boot device is CSA1
Want a different default boot device type Y/N {N} ?
The default boot device is CSA1
Want to modify the default boot device node and unit number Y/N {N} ?
Want to verify bootcode against files on disk Y/N {N} ?
Want to display bootcode files in HEX (from work buffer) Y/N {N} ?
Want to remove any boot code from the buffer Y/N {N} ?
Want to replace the Boot Command Parser Y/N {N} ?
Want to add bootcode for another boot device type Y/N {N} ?
Lo 13 bits of the DU boot device controller IP address in hex is 1468
Want to change this Y/N {N} ?
- - END OF SECTION - WANT TO REPEAT IT Y/N {N} ?
EE> Are you interested in the microcode patch section Y/N {N} ? Y
Want to examine/modify CPU and Patch revision information Y/N {N} ? Y
CPU REV: 18
Want to change this Y/N {N} ?
PATCH REV: 25
Want to change this Y/N {N} ?
Want to compare patches in buffer against patch file on disk Y/N {N} ?
Want to load a new set of microcode patches Y/N {N} ?
Want to list patches (From buffer) Y/N {N} ?
Want to add a single microcode patch Y/N {N} ?
Want to remove a single microcode patch Y/N {N} ?
- - END OF SECTION - WANT TO REPEAT IT Y/N {N} ?
EE> Are you interested in examine/deposit section Y/N {N} ?
EE> Are you interested in the Ethernet section Y/N {N} ?
* END OF PASS *
Want to make another pass Y/N {N} ?
Want to abort this session Y/N {N} ?
Want to write buffer to image file EEPROM.IMA on CSA1 Y/N {N} ?
Want to select destination node for outputing changes Y/N {N} ? Y
NODE NUMBER CPU PROCESOR TYPE
_____________________________________________________________
02 CPU-PRIMARY 2 EEPROM'S
06 CPU-ATTACHED 2 EEPROM'S
Enter destination node number in Hex: {02} : 02
Put control panel switch in update position
Are you ready to continue Y/N {N} ? Y
Update could take several minutes-DO NOT ABORT DURING UPDATE
** Operation was SUCCESSFUL **
Want to exit the utility Y/N {N} ?
**NO MORE CHOICES**
Want to make another pass Y/N {N} ? Y
EE> Are you interested in the general section Y/N {N} ? Y
Want to display VAXBI configuration matrix Y/N {N} ?
Want to display a summary of EEPROM contents (From Work Buffer) Y/N {N} ?
CPU serial number is NI00000000
Want to change this Y/N {N} ?
^C
DS> SYT\T\T
?? Illegal command
\SY\
DS> ST
.. Program: EBUCA-VAX 8200/8300 EEPROM UTILITY and VAXBI CONFIGURATOR, revision
2.4, 1 test,
at 14:39:15.14.
Testing: _KA1
** EBUCA STARTUP **
Do you want help Y/N {N} ?
Source for loading EEPROM work buffer is the primary processor
Want to change this Y/N {N} ? Y
Want to load buffer from initialization file KAINITx.SYS Y/N {N} ?
Want to load buffer from EEPROM saved image on CSA1 Y/N {N} ? Y
EE> Are you interested in the general section Y/N {N} ?
^C
DS> ST
.. Program: EBUCA-VAX 8200/8300 EEPROM UTILITY and VAXBI CONFIGURATOR, revision
2.4, 1 test,
at 14:39:47.16.
Testing: _KA1
** EBUCA STARTUP **
Do you want help Y/N {N} ?
Source for loading EEPROM work buffer is the primary processor
Want to change this Y/N {N} ? Y
Want to load buffer from initialization file KAINITx.SYS Y/N {N} ?
Want to load buffer from EEPROM saved image on CSA1 Y/N {N} ?
Want to load buffer from EEPROM of an attached processor Y/N {N} ? Y
NODE NUMBER CPU PROCESOR TYPE
_____________________________________________________________
02 CPU-PRIMARY 2 EEPROM'S
06 CPU-ATTACHED 2 EEPROM'S
Enter source node number in Hex: {02} : 06
EE> Are you interested in the general section Y/N {N} ? Y
Want to display VAXBI configuration matrix Y/N {N} ?
Want to display a summary of EEPROM contents (From Work Buffer) Y/N {N} ?
CPU serial number is GA81285848
Want to change this Y/N {N} ?
RCX50 selftest is disabled
Want to change this Y/N {N} ?
VAXBI selftest timeout in seconds is 25
Want to change this Y/N {N} ?
FCHIP is enabled
Want to change this Y/N {N} ?
CACHE is enabled
Want to change this Y/N {N} ?
- - END OF SECTION - WANT TO REPEAT IT Y/N {N} ? N
EE> Are you interested in the console section Y/N {N} ?
EE> Are you interested in the boot code section Y/N {N} ?
EE> Are you interested in the microcode patch section Y/N {N} ? Y
Want to examine/modify CPU and Patch revision information Y/N {N} ? Y
CPU REV: 18
Want to change this Y/N {N} ?
PATCH REV: 23
Want to change this Y/N {N} ?
Want to compare patches in buffer against patch file on disk Y/N {N} ?
^C
DS> ST
.. Program: EBUCA-VAX 8200/8300 EEPROM UTILITY and VAXBI CONFIGURATOR, revision
2.4, 1 test,
at 14:41:58.28.
Testing: _KA1
** EBUCA STARTUP **
Do you want help Y/N {N} ?
Source for loading EEPROM work buffer is the primary processor
Want to change this Y/N {N} ?
EE> Are you interested in the general section Y/N {N} ? Y
Want to display VAXBI configuration matrix Y/N {N} ?
Want to display a summary of EEPROM contents (From Work Buffer) Y/N {N} ?
CPU serial number is NI00000000
Want to change this Y/N {N} ? Y
Enter full 10 character serial number: {NI00000000} : GA81285848
RCX50 selftest is enabled
Want to change this Y/N {N} ? Y
VAXBI selftest timeout in seconds is 25
Want to change this Y/N {N} ?
FCHIP is enabled
Want to change this Y/N {N} ?
CACHE is enabled
Want to change this Y/N {N} ?
- - END OF SECTION - WANT TO REPEAT IT Y/N {N} ?
EE> Are you interested in the console section Y/N {N} ?
EE> Are you interested in the boot code section Y/N {N} ?
EE> Are you interested in the microcode patch section Y/N {N} ? Y
Control store chksum is bad
Want to correct it Y/N {N} ?
^C
DS> ST
.. Program: EBUCA-VAX 8200/8300 EEPROM UTILITY and VAXBI CONFIGURATOR, revision
2.4, 1 test,
at 14:43:42.16.
Testing: _KA1
** EBUCA STARTUP **
Do you want help Y/N {N} ?
Source for loading EEPROM work buffer is the primary processor
Want to change this Y/N {N} ? Y
Want to load buffer from initialization file KAINITx.SYS Y/N {N} ?
Want to load buffer from EEPROM saved image on CSA1 Y/N {N} ? Y
EE> Are you interested in the general section Y/N {N} ? Y
Want to display VAXBI configuration matrix Y/N {N} ?
Want to display a summary of EEPROM contents (From Work Buffer) Y/N {N} ?
CPU serial number is GA81182946
Want to change this Y/N {N} ? Y
Enter full 10 character serial number: {GA81182946} : GA81285848
RCX50 selftest is disabled
Want to change this Y/N {N} ?
VAXBI selftest timeout in seconds is 25
Want to change this Y/N {N} ?
FCHIP is enabled
Want to change this Y/N {N} ?
CACHE is enabled
Want to change this Y/N {N} ?
- - END OF SECTION - WANT TO REPEAT IT Y/N {N} ?
EE> Are you interested in the console section Y/N {N} ?
EE> Are you interested in the boot code section Y/N {N} ?
EE> Are you interested in the microcode patch section Y/N {N} ? Y
Want to examine/modify CPU and Patch revision information Y/N {N} ? Y
CPU REV: 18
Want to change this Y/N {N} ?
PATCH REV: 25
Want to change this Y/N {N} ?
Want to compare patches in buffer against patch file on disk Y/N {N} ?
Want to load a new set of microcode patches Y/N {N} ?
Want to list patches (From buffer) Y/N {N} ?
Want to add a single microcode patch Y/N {N} ?
Want to remove a single microcode patch Y/N {N} ?
- - END OF SECTION - WANT TO REPEAT IT Y/N {N} ?
EE> Are you interested in examine/deposit section Y/N {N} ?
EE> Are you interested in the Ethernet section Y/N {N} ?
* END OF PASS *
Want to make another pass Y/N {N} ?
Want to abort this session Y/N {N} ?
Want to write buffer to image file EEPROM.IMA on CSA1 Y/N {N} ?
Want to select destination node for outputing changes Y/N {N} ? Y
NODE NUMBER CPU PROCESOR TYPE
_____________________________________________________________
02 CPU-PRIMARY 2 EEPROM'S
06 CPU-ATTACHED 2 EEPROM'S
Enter destination node number in Hex: {02} : 06
Update could take several minutes-DO NOT ABORT DURING UPDATE
** Operation was SUCCESSFUL **
Want to exit the utility Y/N {N} ?
**NO MORE CHOICES**
Want to make another pass Y/N {N} ? Y
EE> Are you interested in the general section Y/N {N} ?
^C
DS> ST
.. Program: EBUCA-VAX 8200/8300 EEPROM UTILITY and VAXBI CONFIGURATOR, revision
2.4, 1 test,
at 14:46:58.20.
Testing: _KA1
** EBUCA STARTUP **
Do you want help Y/N {N} ?
Source for loading EEPROM work buffer is the primary processor
Want to change this Y/N {N} ?
EE> Are you interested in the general section Y/N {N} ? N
EE> Are you interested in the console section Y/N {N} ?
EE> Are you interested in the boot code section Y/N {N} ?
EE> Are you interested in the microcode patch section Y/N {N} ? Y
Control store chksum is bad
Want to correct it Y/N {N} ?
^C
DS> ST
.. Program: EBUCA-VAX 8200/8300 EEPROM UTILITY and VAXBI CONFIGURATOR, revisionesting: _KA1
** EBUCA STARTUP **
Do you want help Y/N {N} ?
Source for loading EEPROM work buffer is the primary processor
Want to change this Y/N {N} ? Y
Want to load buffer from initialization file KAINITx.SYS Y/N {N} ?
Want to load buffer from EEPROM saved image on CSA1 Y/N {N} ? Y
EE> Are you interested in the general section Y/N {N} ? Y
Want to display VAXBI configuration matrix Y/N {N} ?
Want to display a summary of EEPROM contents (From Work Buffer) Y/N {N} ?
CPU serial number is GA81182946
Want to change this Y/N {N} ? Y
Enter full 10 character serial number: {GA81182946} : NI00000000
RCX50 selftest is disabled
Want to change this Y/N {N} ? Y
VAXBI selftest timeout in seconds is 25
Want to change this Y/N {N} ?
FCHIP is enabled
Want to change this Y/N {N} ?
CACHE is enabled
Want to change this Y/N {N} ?
- - END OF SECTION - WANT TO REPEAT IT Y/N {N} ?
EE> Are you interested in the console section Y/N {N} ?
EE> Are you interested in the boot code section Y/N {N} ?
EE> Are you interested in the microcode patch section Y/N {N} ? Y
Want to examine/modify CPU and Patch revision information Y/N {N} ?
Want to compare patches in buffer against patch file on disk Y/N {N} ?
Want to load a new set of microcode patches Y/N {N} ?
Want to list patches (From buffer) Y/N {N} ?
Want to add a single microcode patch Y/N {N} ?
Want to remove a single microcode patch Y/N {N} ?
- - END OF SECTION - WANT TO REPEAT IT Y/N {N} ?
EE> Are you interested in examine/deposit section Y/N {N} ?
EE> Are you interested in the Ethernet section Y/N {N} ?
* END OF PASS *
Want to make another pass Y/N {N} ?
Want to abort this session Y/N {N} ?
Want to write buffer to image file EEPROM.IMA on CSA1 Y/N {N} ?
Want to select destination node for outputing changes Y/N {N} ? Y
NODE NUMBER CPU PROCESOR TYPE
_____________________________________________________________
02 CPU-PRIMARY 2 EEPROM'S
06 CPU-ATTACHED 2 EEPROM'S
Enter destination node number in Hex: {02} : 02
Put control panel switch in update position
Are you ready to continue Y/N {N} ? Y
Update could take several minutes-DO NOT ABORT DURING UPDATE
** Operation was SUCCESSFUL **
Want to exit the utility Y/N {N} ?
**NO MORE CHOICES**
Want to make another pass Y/N {N} ? YC
^C
Want to abort this session Y/N {N} ?
Want to write buffer to image file EEPROM.IMA on CSA1 Y/N {N} ?
^C
Want to select destination node for outputing changes Y/N {N} ?
**NO MORE CHOICES**
DS> ST
.. Program: EBUCA-VAX 8200/8300 EEPROM UTILITY and VAXBI CONFIGURATOR, revision
2.4, 1 test,
at 14:50:22.16.
Testing: _KA1
** EBUCA STARTUP **
Do you want help Y/N {N} ?
Source for loading EEPROM work buffer is the primary processor
Want to change this Y/N {N} ?
EE> Are you interested in the general section Y/N {N} ?
EE> Are you interested in the console section Y/N {N} ?
EE> Are you interested in the boot code section Y/N {N} ?
EE> Are you interested in the microcode patch section Y/N {N} ? Y
Control store chksum is bad
Want to correct it Y/N {N} ?
^C
DS> ST
.. Program: EBUCA-VAX 8200/8300 EEPROM UTILITY and VAXBI CONFIGURATOR, revision
2.4, 1 test,
at 14:51:48.14.
Testing: _KA1
** EBUCA STARTUP **
Do you want help Y/N {N} ?
Source for loading EEPROM work buffer is the primary processor
Want to change this Y/N {N} ? Y
Want to load buffer from initialization file KAINITx.SYS Y/N {N} ?
Want to load buffer from EEPROM saved image on CSA1 Y/N {N} ? Y
EE> Are you interested in the general section Y/N {N} ?
EE> Are you interested in the console section Y/N {N} ?
EE> Are you interested in the boot code section Y/N {N} ?
EE> Are you interested in the microcode patch section Y/N {N} ? Y
Want to examine/modify CPU and Patch revision information Y/N {N} ?
Want to compare patches in buffer against patch file on disk Y/N {N} ?
Want to load a new set of microcode patches Y/N {N} ?
Want to list patches (From buffer) Y/N {N} ?
Want to add a single microcode patch Y/N {N} ?
Want to remove a single microcode patch Y/N {N} ?
- - END OF SECTION - WANT TO REPEAT IT Y/N {N} ?
EE> Are you interested in examine/deposit section Y/N {N} ?
EE> Are you interested in the Ethernet section Y/N {N} ?
* END OF PASS *
Want to make another pass Y/N {N} ?
Want to abort this session Y/N {N} ?
Want to write buffer to image file EEPROM.IMA on CSA1 Y/N {N} ?
Want to select destination node for outputing changes Y/N {N} ? Y
NODE NUMBER CPU PROCESOR TYPE
_____________________________________________________________
02 CPU-PRIMARY 2 EEPROM'S
06 CPU-ATTACHED 2 EEPROM'S
Enter destination node number in Hex: {02} : 02
Put control panel switch in update position
Are you ready to continue Y/N {N} ? Y
Update could take several minutes-DO NOT ABORT DURING UPDATE
** Operation was SUCCESSFUL **
Want to exit the utility Y/N {N} ?
**NO MORE CHOICES**
Want to make another pass Y/N {N} ?
^C
Want to abort this session Y/N {N} ?
Want to write buffer to image file EEPROM.IMA on CSA1 Y/N {N} ?
Want to select destination node for outputing changes Y/N {N} ?
**NO MORE CHOICES**
DS>
DS> ST
.. Program: EBUCA-VAX 8200/8300 EEPROM UTILITY and VAXBI CONFIGURATOR, revision
2.4, 1 test,
at 14:53:56.18.
Testing: _KA1
** EBUCA STARTUP **
Do you want help Y/N {N} ?
Source for loading EEPROM work buffer is the primary processor
Want to change this Y/N {N} ?
EE> Are you interested in the general section Y/N {N} ?
EE> Are you interested in the console section Y/N {N} ?
EE> Are you interested in the boot code section Y/N {N} ?
EE> Are you interested in the microcode patch section Y/N {N} ?
EE> Are you interested in examine/deposit section Y/N {N} ?
^C
DS> ST
.. Program: EBUCA-VAX 8200/8300 EEPROM UTILITY and VAXBI CONFIGURATOR, revision
2.4, 1 test,
at 14:54:27.16.
Testing: _KA1
** EBUCA STARTUP **
Do you want help Y/N {N} ?
Source for loading EEPROM work buffer is the primary processor
Want to change this Y/N {N} ?
EE> Are you interested in the general section Y/N {N} ?
EE> Are you interested in the console section Y/N {N} ?
EE> Are you interested in the boot code section Y/N {N} ?
EE> Are you interested in the microcode patch section Y/N {N} ? Y
Control store chksum is bad
Want to correct it Y/N {N} ?
^C
DS> ST
.. Program: EBUCA-VAX 8200/8300 EEPROM UTILITY and VAXBI CONFIGURATOR, revision
2.4, 1 test,
at 14:55:16.16.
Testing: _KA1
** EBUCA STARTUP **
Do you want help Y/N {N} ?
Source for loading EEPROM work buffer is the primary processor
Want to change this Y/N {N} ? T\T\Y
Want to load buffer from initialization file KAINITx.SYS Y/N {N} ?
Want to load buffer from EEPROM saved image on CSA1 Y/N {N} ?
Want to load buffer from EEPROM of an attached processor Y/N {N} ? Y
NODE NUMBER CPU PROCESOR TYPE
________________________________________________________
02 CPU-PRIMARY 2 EEPROM'S
06 CPU-ATTACHED 2 EEPROM'S
Enter source node number in Hex: {02} : 06
EE> Are you interested in the general section Y/N {N} ?
EE> Are you interested in the console section Y/N {N} ?
EE> Are you interested in the boot code section Y/N {N} ?
EE> Are you interested in the microcode patch section Y/N {N} ? Y
Want to examine/modify CPU and Patch revision information Y/N {N} ?
Want to compare patches in buffer against patch file on disk Y/N {N} ?
Want to load a new set of microcode patches Y/N {N} ?
Want to list patches (From buffer) Y/N {N} ?
Want to add a single microcode patch Y/N {N} ?
Want to remove a single microcode patch Y/N {N} ?
- - END OF SECTION - WANT TO REPEAT IT Y/N {N} ?
^C
DS> ST
.. Program: EBUCA-VAX 8200/8300 EEPROM UTILITY and VAXBI CONFIGURATOR, revision
2.4, 1 test,
at 14:56:38.12.
Testing: _KA1
** EBUCA STARTUP **
Do you want help Y/N {N} ?
Source for loading EEPROM work buffer is the primary processor
Want to change this Y/N {N} ? Y
Want to load buffer from initialization file KAINITx.SYS Y/N {N} ?
Want to load buffer from EEPROM saved image on CSA1 Y/N {N} ?
Want to load buffer from EEPROM of an attached processor Y/N {N} ? Y
NODE NUMBER CPU PROCESOR TYPE
_____________________________________________________________
02 CPU-PRIMARY 2 EEPROM'S
06 CPU-ATTACHED 2 EEPROM'S
Enter source node number in Hex: {02} : 06
EE> Are you interested in the general section Y/N {N} ?
EE> Are you interested in the console section Y/N {N} ?
EE> Are you interested in the boot code section Y/N {N} ?
EE> Are you interested in the microcode patch section Y/N {N} ? Y
Want to examine/modify CPU and Patch revision information Y/N {N} ? Y
CPU REV: 18
Want to change this Y/N {N} ?
PATCH REV: 25
Want to change this Y/N {N} ?
^C
DS> DIR
Directory CSA1:[SYSMAINT]
CSBOOKA.SYS;2 DUBOOKA.SYS;17 EBSAA.EXE;1 EBUCA.COM;3
EBUCA.EXE;13 EBUCA.HLP;19 EEPROM.IMA;1 ETBOOKA.SYS;11
FG80.VI0;1 KA0023.PAT;13 KA021B.PAT;2 KA825.SYS;1
KA8BOO.SYS;1 KA8BOO2.SYS;1 KAINIT.SYS;6 KAINIT2.SYS;1
MUBOOKA.SYS;14
Total of 17 files.
DS>
?02
PC = 00022AA0
>>>T
#�
#ABCDEFGHIJK..N#
. . 2 . . 5 6 7 8 . . B C D E F
06000000
?01
PC = 00000002
>>>B
. . 2 . . 5 6 7 8 . . B C D E F
06000000Z
VAX DIAGNOSTIC SOFTWARE
PROPERTY OF
DIGITAL EQUIPMENT CORPORATION
***CONFIDENTIAL AND PROPRIETARY***
Use Authorized Only Pursuant to a Valid Right-to-Use License
Copyright, Digital Equipment Corporation, 1987. All Rights Reserved.
DIAGNOSTIC SUPERVISOR. ZZ-EBSAA-10.9-885 8-SEP-1987 15:00:07
DS>
?02
PC = 00024870
>>>H
PC = 00024870
>>>
Exiting TRANS mode [protocol on]...
REM> TR
Entering TRANS mode [protocol off] (^A to exit)...
#�
#ABCDEFGHIJK..N#
. . 2 . . 5 6 7 8 . . B C D E F
06000000
?03
PC = 00000002
>>>B CSA1
. . 2 . . 5 6 7 8 . . B C D E F
06000000
?02
PC = 00023A60
>>>H
PC = 00023A60
>>>B CSA1
. . 2 . . 5 6 7 8 . . B C D E F
06000000Z
VAX DIAGNOSTIC SOFTWARE
PROPERTY OF
DIGITAL EQUIPMENT CORPORATION
***CONFIDENTIAL AND PROPRIETARY***
Use Authorized Only Pursuant to a Valid Right-to-Use License
Copyright, Digital Equipment Corporation, 1987. All Rights Reserved.
DIAGNOSTIC SUPERVISOR. ZZ-EBSAA-10.9-885 8-SEP-1987 15:06:07
DS> ATT K\K TTA\
DS> @EBUCA
.. Program: EBUCA-VAX 8200/8300 EEPROM UTILITY and VAXBI CONFIGURATOR, revision
2.4, 1 test,
at 15:07:12.91.
Testing: _KA0
** EBUCA STARTUP **
Do you want help Y/N {N} ?
Source for loading EEPROM work buffer is the primary processor
Want to change this Y/N {N} ? Y
Want to load buffer from initialization file KAINITx.SYS Y/N {N} ?
Want to load buffer from EEPROM saved image on CSA1 Y/N {N} ? Y
EE> Are you interested in the general section Y/N {N} ?
EE> Are you interested in the console section Y/N {N} ?
EE> Are you interested in the boot code section Y/N {N} ?
EE> Are you interested in the microcode patch section Y/N {N} ? Y
Want to examine/modify CPU and Patch revision information Y/N {N} ?
Want to compare patches in buffer against patch file on disk Y/N {N} ?
Want to load a new set of microcode patches Y/N {N} ?
Want to list patches (From buffer) Y/N {N} ?
Want to add a single microcode patch Y/N {N} ?
Want to remove a single microcode patch Y/N {N} ?
- - END OF SECTION - WANT TO REPEAT IT Y/N {N} ?
EE> Are you interested in examine/deposit section Y/N {N} ?
EE> Are you interested in the Ethernet section Y/N {N} ?
* END OF PASS *
Want to make another pass Y/N {N} ?
Want to abort this session Y/N {N} ?
Want to write buffer to image file EEPROM.IMA on CSA1 Y/N {N} ?
Want to select destination node for outputing changes Y/N {N} ? Y
NODE NUMBER CPU PROCESOR TYPE
_____________________________________________________________
02 CPU-PRIMARY 2 EEPROM'S
06 CPU-ATTACHED 2 EEPROM'S
Enter destination node number in Hex: {02} : 02
Put control panel switch in update position
Are you ready to continue Y/N {N} ? Y
Update could take several minutes-DO NOT ABORT DURING UPDATE
** Operation was SUCCESSFUL **
Want to exit the utility Y/N {N} ? Y
.. End of run, 0 errors detected, pass count is 1,
time is 8-SEP-1987 15:08:49.94
DS> ST
.. Program: EBUCA-VAX 8200/8300 EEPROM UTILITY and VAXBI CONFIGURATOR, revision
2.4, 1 test,
at 15:08:57.65.
Testing: _KA0
** EBUCA STARTUP **
Do you want help Y/N {N} ?
Source for loading EEPROM work buffer is the primary processor
Want to change this Y/N {N} ?
EE> Are you interested in the general section Y/N {N} ?
EE> Are you interested in the console section Y/N {N} ?
EE> Are you interested in the boot code section Y/N {N} ?
EE> Are you interested in the microcode patch section Y/N {N} ? Y
Want to examine/modify CPU and Patch revision information Y/N {N} ? Y
CPU REV: 18
Want to change this Y/N {N} ? N
PATCH REV: 25
Want to change this Y/N {N} ?
Want to compare patches in buffer against patch file on disk Y/N {N} ?
Want to load a new set of microcode patches Y/N {N} ?
Want to list patches (From buffer) Y/N {N} ?
Want to add a single microcode patch Y/N {N} ?
Want to remove a single microcode patch Y/N {N} ?
- - END OF SECTION - WANT TO REPEAT IT Y/N {N} ?
^C
DS> ST
.. Program: EBUCA-VAX 8200/8300 EEPROM UTILITY and VAXBI CONFIGURATOR, revision
2.4, 1 test,
at 15:10:09.72.
Testing: _KA0
** EBUCA STARTUP **
Do you want help Y/N {N} ?
Source for loading EEPROM work buffer is the primary processor
Want to change this Y/N {N} ?
EE> Are you interested in the general section Y/N {N} ? Y
^C
DS> ST
.. Program: EBUCA-VAX 8200/8300 EEPROM UTILITY and VAXBI CONFIGURATOR, revision
2.4, 1 test,
at 15:10:35.72.
Testing: _KA0
** EBUCA STARTUP **
Do you want help Y/N {N} ?
Source for loading EEPROM work buffer is the primary processor
Want to change this Y/N {N} ? T\T\Y
Want to load buffer from initialization file KAINITx.SYS Y/N {N} ?
Want to load buffer from EEPROM saved image on CSA1 Y/N {N} ? Y
EE> Are you interested in the general section Y/N {N} ? Y
Want to display VAXBI configuration matrix Y/N {N} ?
Want to display a summary of EEPROM contents (From Work Buffer) Y/N {N} ?
CPU serial number is GA81182946
Want to change this Y/N {N} ? Y
Enter full 10 character serial number: {GA81182946} : NI00000000
RCX50 selftest is disabled
Want to change this Y/N {N} ? Y
VAXBI selftest timeout in seconds is 25
Want to change this Y/N {N} ?
FCHIP is enabled
Want to change this Y/N {N} ?
CACHE is enabled
Want to change this Y/N {N} ?
- - END OF SECTION - WANT TO REPEAT IT Y/N {N} ?
EE> Are you interested in the console section Y/N {N} ?
EE> Are you interested in the boot code section Y/N {N} ?
EE> Are you interested in the microcode patch section Y/N {N} ? Y
Want to examine/modify CPU and Patch revision information Y/N {N} ? Y
CPU REV: 18
Want to change this Y/N {N} ?
PATCH REV: 25
Want to change this Y/N {N} ?
Want to compare patches in buffer against patch file on disk Y/N {N} ?
Want to load a new set of microcode patches Y/N {N} ?
Want to list patches (From buffer) Y/N {N} ?
Want to add a single microcode patch Y/N {N} ?
Want to remove a single microcode patch Y/N {N} ?
- - END OF SECTION - WANT TO REPEAT IT Y/N {N} ?
EE> Are you interested in examine/deposit section Y/N {N} ?
EE> Are you interested in the Ethernet section Y/N {N} ?
* END OF PASS *
Want to make another pass Y/N {N} ?
Want to abort this session Y/N {N} ?
Want to write buffer to image file EEPROM.IMA on CSA1 Y/N {N} ?
Want to select destination node for outputing changes Y/N {N} ? Y
NODE NUMBER CPU PROCESOR TYPE
_____________________________________________________________
02 CPU-PRIMARY 2 EEPROM'S
06 CPU-ATTACHED 2 EEPROM'S
Enter destination node number in Hex: {02} : 02
Put control panel switch in update position
Are you ready to continue Y/N {N} ? Y
Update could take several minutes-DO NOT ABORT DURING UPDATE
** Operation was SUCCESSFUL **
Want to exit the utility Y/N {N} ?
**NO MORE CHOICES**
Want to make another pass Y/N {N} ? Y
EE> Are you interested in the general section Y/N {N} ?
^C
DS> ST
.. Program: EBUCA-VAX 8200/8300 EEPROM UTILITY and VAXBI CONFIGURATOR, revision
2.4, 1 test,
at 15:12:54.66.
Testing: _KA0
** EBUCA STARTUP **
Do you want help Y/N {N} ?
Source for loading EEPROM work buffer is the primary processor
Want to change this Y/N {N} ?
EE> Are you interested in the general section Y/N {N} ?
EE> Are you interested in the console section Y/N {N} ?
EE> Are you interested in the boot code section Y/N {N} ?
EE> Are you interested in the microcode patch section Y/N {N} ? Y
Want to examine/modify CPU and Patch revision information Y/N {N} ? Y
CPU REV: 18
Want to change this Y/N {N} ?
PATCH REV: 25
Want to change this Y/N {N} ?
Want to compare patches in buffer against patch file on disk Y/N {N} ?
Want to load a new set of microcode patches Y/N {N} ?
Want to list patches (From buffer) Y/N {N} ?
Want to add a single microcode patch Y/N {N} ?
Want to remove a single microcode patch Y/N {N} ?
^C
DS>
?02
PC = 00022AC1
>>>D
?44
>>>B DUA03^P
>>>B DUA3
. . 2 . . 5 6 7 8 . . B C D E F
06000000
?06
PC = 0000FD05
>>>B DU3^P
>>>B DUA^P
>>>B
. . 2 . . 5 6 7 8 . . B C D E F
06000000
!DEFBOO.CMD : Boot command file to boot a VAX 8200/8300 from an HSC disk.
!
D/G 0 20 ! CI Port Device Type Code
D/G 1 8 ! n = CI adaptor's VAXBI node number
D/G 2 0100 ! Use the HSC controller at CI node p
D/G 3 0 ! u = Disk drive unit number
D/G 5 10000000 ! r = system root [SYSr...],Software Boot Flags
D/G E 200 ! Address of Working Memory+^X200
LOAD VMB.EXE/START:200 ! Load Primary Bootstrap
START 200 ! Start Primary Bootstrap LETS GO..
VAX/VMS Version V5.0-1 Major version id = 1 Minor version id = 0
%CNXMAN, Using remote access method for quorum disk
%SMP-I-CPUBOOTED, CPU #06 has joined the PRIMARY CPU in multiprocessor operation
waiting to form or join a VAXcluster system
%CNXMAN, Sending VAXcluster membership request to system N1
%CNXMAN, Now a VAXcluster member -- system N2
%CNXMAN, Using local access method for quorum disk
%CNXMAN, Established "connection" to quorum disk
$! Copyright (c) 1988 Digital Equipment Corporation. All rights reserved.
%%%%%%%%%%% OPCOM 7-SEP-1988 15:24:15.68 %%%%%%%%%%%
Logfile has been initialized by operator _N2$OPA0:
Logfile is SYS$SYSROOT:[SYSMGR]OPERATOR.LOG;89
%%%%%%%%%%% OPCOM 7-SEP-1988 15:24:16.40 %%%%%%%%%%%
09:54:51.53 Node N2 (csid 00000000) is using remote access method for quorum disk
%%%%%%%%%%% OPCOM 7-SEP-1988 15:24:16.49 %%%%%%%%%%%
15:23:12.27 Node N2 (csid 00010002) is now a VAXcluster member
%%%%%%%%%%% OPCOM 7-SEP-1988 15:24:16.55 %%%%%%%%%%%
15:23:15.77 Node N2 (csid 00010002) is using local access method for quorum disk
%%%%%%%%%%% OPCOM 7-SEP-1988 15:24:16.62 %%%%%%%%%%%
15:23:15.84 Node N2 (csid 00010002) re-established "connection" to quorum disk
%%%%%%%%%%% OPCOM 7-SEP-1988 15:24:16.71 %%%%%%%%%%%
Operator _N1$OPA0: has been enabled, username SYSTEM
%LICENSE-I-LOADED, DEC DVNETRTG was successfully loaded with 0 units
%LICENSE-I-LOADED, DEC VAXCLUSTER was successfully loaded with 0 units
%SYSTEM-W-ALLSTARTED, all configured processors are already started
%MOUNT-I-MOUNTED, DATA mounted on _HSC001$DUA1:
%MOUNT-I-MOUNTED, SHADOW mounted on _HSC001$DUA2:
%MOUNT-I-MOUNTED, DEVELOPMENT mounted on _HSC001$DUA3:
%RUN-S-PROC_ID, identification of created process is 2040010D
%%%%%%%%%%% OPCOM 7-SEP-1988 15:25:07.41 %%%%%%%%%%%
Message from user DECNET on N2
DECnet starting
%NCP-I-NOINFO, No information in database
%NCP-I-NOINFO, No information in database
%%%%%%%%%%% OPCOM 7-SEP-1988 15:25:12.01 %%%%%%%%%%%
Message from user DECNET on N2
Error opening permanent proxy database
%DCL-I-SUPERSEDE, previous value of MOM$LOAD has been superseded
%%%%%%%%%%% OPCOM 7-SEP-1988 15:25:17.56 %%%%%%%%%%%
Message from user DECNET on N2
DECnet event 4.10, circuit up
From node 1.4 (N2), 7-SEP-1988 15:25:17.18
Circuit BNA-0
%%%%%%%%%%% OPCOM 7-SEP-1988 15:25:18.38 %%%%%%%%%%% (from node N1 at 7-SEP-1988 15:25:
18.57)
Message from user DECNET on N1
DECnet event 4.15, adjacency up
From node 1.3 (N1), 7-SEP-1988 15:25:18.50
Circuit BNA-0, Adjacent node = 1.4 (N2)
%NCP-I-NOINFO, No information in database
%%%%%%%%%%% OPCOM 7-SEP-1988 15:25:21.99 %%%%%%%%%%%
Message from user DECNET on N2
DECnet event 4.15, adjacency up
From node 1.4 (N2), 7-SEP-1988 15:25:17.37
Circuit BNA-0, Adjacent node = 1.3
%RUN-S-PROC_ID, identification of created process is 2040010F
LCP Characteristics
Node name = \N2\
Node Identification = \SYS$ANNOUNCE\
Groups = (0)
Multicast timer = 60 seconds
LAT Version = 5.1 LAT Protocol is inactive
Service Names and Ids:
Service name : \N2\ rating : <auto>
ID : \VAX Cluster\
LCP Characteristics
Node name = \N2\
Node Identification = \SYS$ANNOUNCE\
Groups = (0)
Multicast timer = 60 seconds
LAT Version = 5.1 LAT Protocol is active
Service Names and Ids:
Service name : \N2\ rating : <auto>
ID : \VAX Cluster\
Node Links:
Link name = \LAT$LINK\
Link device = \ETA0:\
Groups = ()
Link-specific services:
Status = Active
%LAT-I-STARTED, LAT terminal port driver started
%JBC-E-STARTED, queue already started
%JBC-E-STARTED, queue already started
%SET-I-INTSET, login interactive limit = 64, current interactive value = 0
7-SEP-1988 15:25:57
SYSTEM job terminated at 7-SEP-1988 15:26:01.20
Accounting information:
Buffered I/O count: 1346 Peak working set size: 850
Direct I/O count: 615 Peak page file size: 3530
Page faults: 11636 Mounted volumes: 3
Charged CPU time: 0 00:01:29.77 Elapsed time: 0 00:02:40.82
Username: FIELD
Password:
Welcome to VAX/VMS version V5.0-1 on node N2
Last interactive login on Wednesday, 7-SEP-1988 14:35
�3[1m Welcome to the RW VAXCluster[0m
�4[1m Welcome to the RW VAXCluster[0m
Z>
N2_DEC_>>SH/CPU
%DCL-W-NOQUAL, qualifiers not allowed - supply only verb and parameters
\CPU\
N2_DEC_>>HELP SHOW CPU
<[1;1f[J
SHOW
CPU
Displays the current state of the processors in a VMS multiprocessing
system.
Applies only to VMS multiprocessing systems. Requires change mode to
kernel (CMKRNL) privilege.
Format:
SHOW CPU [cpu-id,...]
Additional information available:
Parameter Qualifiers
/ACTIVE /ALL /BRIEF /FULL /SUMMARY
Examples
Press RETURN to continue ... EX
[1;1f[J
SHOW
CPU
Examples
1. $ SHOW CPU
SOWHAT, A VAX 8800
Multiprocessing is ENABLED. MULTIPROCESSING Sysgen parameter = 02
Minimum multiprocessing revision levels -- CPU: 0 uCODE: 0 UWCS: 0.
PRIMARY CPU = 01
Active CPUs: 00 01
Configured CPUs: 00 01
This SHOW CPU command produces a configuration summary of all
configured processors in the VAX 8800 system SOWHAT. The primary
processor is CPU 01, and all configured processors are active.
Press RETURN to continue ...
[1;1f[J
2. $ SHOW CPU /BRIEF
SOWHAT, A VAX 8800
Multiprocessing is ENABLED. MULTIPROCESSING Sysgen parameter = 02
Minimum multiprocessing revision levels -- CPU: 0 uCODE: 0 UWCS: 0.
PRIMARY CPU = 01
CPU 00 is in RUN state
Current Process: AIREGIN EPID = 4A8001E5
CPU 01 is in RUN state
Current Process: ***None***
This SHOW CPU/BRIEF command produces
7[7m Interrupt [m8
N2_DEC_>>SH CPU/FUL
%SYSTEM-F-NOPRIV, no privilege for attempted operation
N2_DEC_>>SET PROC/PRIV=CMK
N2_DEC_>>
[K N2_DEC_>>SET PROC/PRIV=CMK
[K N2_DEC_>>SH CPU/FUL
N2, a VAX 8350
Multiprocessing is ENABLED. Streamlined synchronization image loaded.
Minimum multiprocessing revision levels: CPU = 2 uCODE = 20 PATCH = 21.
PRIMARY CPU = 02
CPU 02 is in RUN state
Current Process: *** None ***
Revision levels: CPU = 2 uCODE = 20 PATCH = 25.
Capabilities of this CPU:
PRIMARY
Processes which can only execute on this CPU:
*** None ***
CPU 06 is in RUN state
Current Process: FIELD PID = 20400110
Revision levels: CPU = 2 uCODE = 20 PATCH = 25.
Capabilities of this CPU:
*** None ***
Processes which can only execute on this CPU:
*** None ***
N2_DEC_>>SH SH SYS
VAX/VMS V5.0-1 on node N2 7-SEP-1988 15:28:43.69 Uptime 0 00:05:48
Pid Process Name State Pri I/O CPU Page flts Ph.Mem
20400101 SWAPPER HIB 16 0 0 00:00:00.84 0 0
20400106 ERRFMT HIB 9 27 0 00:00:00.56 78 141
20400107 CACHE_SERVER HIB 16 6 0 00:00:00.28 65 134
20400108 CLUSTER_SERVER HIB 10 10 0 00:00:00.66 123 294
20400109 OPCOM HIB 8 43 0 00:00:01.30 177 244
2040010A JOB_CONTROL HIB 9 63 0 00:00:01.40 178 441
2040010B CONFIGURE HIB 8 12 0 00:00:00.49 103 188
2040010C SMISERVER HIB 9 53 0 00:00:02.10 230 700
2040010D NETACP HIB 10 35 0 00:00:03.72 200 415
2040010E EVL HIB 6 56 0 00:00:01.74 371 89 N
2040010F REMACP HIB 8 8 0 00:00:00.31 70 76
20400110 FIELD CUR 6 4 206 0 00:00:04.66 611 421
N2_DEC_>>MON CLUS
%MONITOR-I-ESTABCON, establishing connection to remote node(s)...
<(B[1;1f[J[1;29fVAX/VMS Monitor Utility[24;1f [24;34f [24;70f [2;1f
[7m CLUSTER STATISTICS [0m[1;1fStatistic: CURRENT[3;42f|[4;42f|[5;42f|[6;42f|[7;42f|
[8;42f|[9;42f|[10;42f|[11;42f|[12;42f|[13;1f-----------------------------------------+---------
-----------------------------[14;42f|[15;42f|[16;42f|[17;42f|[18;42f|[19;42f|[20;42f|[21;42f
|[22;42f|[23;42f|[3;20fCPU[5;1fCPU Busy[5;21f0 25 50 75 100[6;21f+----+----+----+----+
[7;21f|[8;21f|[9;21f|[10;21f|[11;21f|[12;21f|[3;58fMEMORY[5;43f%Memory In Use[5;60f0 25
50 75 100[6;60f+----+----+----+----+[7;60f|[8;60f|[9;60f|[10;60f|[11;60f|[12;60f|[14;20fD
ISK[16;1fI/O Operation Rate[16;21f0 25 50 75 100[17;21f+----+----+----+----+[18;21f|[19;
21f|[20;21f|[21;21f|[22;21f|[23;21f|[14;59fLOCK[16;43fTot ENQ/DEQ Rate[16;60f0 125 250 375
500[17;60f+----+----+----+----+[18;60f|[19;60f|[20;60f|[21;60f|[22;60f|[23;60f|[18;1fHSC00
1$DUA0: [19;1fHSC001$DUA3: [20;1fHSC001$DUA1: [21;1fHSC001$DUA2: [22;1f [23
;1f [1;57f 7-SEP-1988[1;69f15:29:17[7;1fN2 [7;13f 10[7;22f(0aa
(B[8;1fN1 [8;13f 4[8;22f(0 (B[9;1f [9;13f
[9;22f(0 (B[10;1f [10;13f [10;22f(0 (B
[11;1f [11;13f [11;22f(0 (B[12;1f [12;13f [12;
22f(0 (B[7;43fN1 [7;52f 6[7;61f(0a (B[8;43f
N2 [8;52f 2[8;61f(0 (B[9;43f [9;52f [9;61f(0
(B[10;43f [10;52f [10;61f(0 (B[11;43f
[11;52f [11;61f(0 (B[12;43f [12;52f [12;61f(0
(B[18;17f [18;22f(0 (B[19;17f [19;22f(0
(B[20;17f [20;22f(0 (B[21;17f [21;22f(0 (B
[22;17f [22;22f(0 (B[23;17f [23;22f(0 (B[18;43
fN1 [18;52f [18;61f(0 (B[19;43fN2 [19;52f [19;61f(
0 (B[20;43f [20;52f [20;61f(0 (B[21;43f
[21;52f [21;61f(0 (B[22;43f [22;52f [22;61f(0
(B[23;43f [23;52f [23;61f(0 (B[18;1fHSC0
01$DUA3: [19;1fHSC001$DUA0: [20;1fHSC001$DUA1: [21;1fHSC001$DUA2: [22;1f [2
3;1f [1;57f 7-SEP-1988[1;69f15:29:35[7;1fN2 [7;13f 5[7;22f(0a
(B[8;1fN1 [8;13f 4[8;22f(0 (B[9;1f [9;13f
[9;22f(0 (B[10;1f [10;13f [10;22f(0 (B
[11;1f [11;13f [11;22f(0 (B[12;1f [12;13f [12
;22f(0 (B[7;43fN1 [7;52f 6[7;61f(0a (B[8;43
fN2 [8;52f 2[8;61f(0 (B[9;43f [9;52f [9;61f(0
(B[10;43f [10;52f [10;61f(0 (B[11;43f
[11;52f [11;61f(0 (B[12;43f [12;52f [12;61f(0
(B[18;17f [18;22f(0 (B[19;17f [19;22f(0
(B[20;17f [20;22f(0 (B[21;17f [21;22f(0 (
B[22;17f [22;22f(0 (B[23;17f [23;22f(0 (B[18;4
3fN2 [18;52f [18;61f(0 (B[19;43fN1 [19;52f [19;61f
(0 (B[20;43f [20;52f [20;61f(0 (B[21;43f
[21;52f [21;61f(0 (B[22;43f [22;52f [22;61f(0
(B[23;43f [23;52f [23;61f(0 (B(B[1;7;
4m
[0m
[24;1f
N2_DEC_>>SH U
VAX/VMS Interactive Users
7-SEP-1988 15:29:57.50
Total number of interactive users = 1
Username Process Name PID Terminal
FIELD FIELD 20400110 OPA0:
N2_DEC_>>PHONE FIE
Exiting TRANS mode [protocol on]...
REM> TALK
Enter talk mode ....( ^Z to exit )
MSG> IAN ALL SEEMS TO WORKING OK PATCHES REFLECT UPDATED VERSION
MSG>
CAN YOU SEE THIS?
MSG>
MSG>
MSG>
MSG>
MSG>
MSG>
MSG>
Exit talk mode ....
REM> T
Entering TRANS mode [protocol off] (^A to exit)...
N2_DEC_>>SH U
VAX/VMS Interactive Users
7-SEP-1988 15:31:29.52
Total number of interactive users = 1
Username Process Name PID Terminal
FIELD FIELD 20400110 OPA0:
N2_DEC_>>SH LCUS
%DCL-W-IVKEYW, unrecognized keyword - check validity and spelling
\LCUS\
N2_DEC_>>SH CLUS
)0[4l=)0[4l[1;24r[;H[2J[;H[2J[;H[2J[;H[2J[;H[2J[;H[2J[1;1HView of Cluster from sy
stem ID 1028 node: N2[1;61H7-SEP-1988 15:31:45[2;1Hlqqqqqqqqqqqqqqqqqqqwqqqqqqqqqk[3;1Hx
SYSTEMS x MEMBERS x[4;1Htqqqqqqqqwqqqqqqqqqqnqqqqqqqqqu[5;1Hx NODE x SOFTWARE
x STATUS x[6;1Htqqqqqqqqnqqqqqqqqqqnqqqqqqqqqu[7;1Hx N2 x VMS V5.0 x MEMBER x[
8;1Hx HSC001 x HSC V350 x[8;31Hx[9;1Hx N1 x VMS V5.0 x MEMBER x[10;1Hmqqqqq
qqqvqqqqqqqqqqvqqqqqqqqqj[1;1H[m>[1;1H[24;1H
N2_DEC_>>SH U
VAX/VMS Interactive Users
7-SEP-1988 15:32:33.51
Total number of interactive users = 1
Username Process Name PID Terminal
FIELD FIELD 20400110 OPA0:
N2_DEC_>>LO
FIELD logged out at 7-SEP-1988 15:33:36.51
Exiting TRANS mode [protocol on]...
REM> DISC
MOUNTFORD disconnected at 7-SEP-1988 15:31:45.75
| T.R | Title | User | Personal
Name | Date | Lines |
|---|
| 29.1 | KA0029.pat | KERNEL::MOUNTFORD | | Fri Aug 11 1989 16:00 | 2 |
| For those who didn't know, Bob has put the latest version of micrcode
in RDC$common, called KA0029.PAT.
|
| 29.2 | Whats new in KA0029.PAT | KERNEL::WRIGHTON | Pass me a +L-14005 | Fri Sep 01 1989 09:43 | 125 |
|
________________________________________________________________________
| | SDC Release No: 36 Sheet 1 of 2 |
| ## ## ## ## ## |________________________________________|
| ## # # ## ## ## # ## | |
| ## # ## ## ## # ## | S C O R P I O |
| ## ## ## ## ## |________________________________________|
| ## ## ## ## ## | Microcode Implementation Notice |
|_______________________________|________________________________________|
| Originator: Carrie Thompson Date: June 20, 1989 |
| Phone: 247-2088 LOC: TWO/A12 Node: SASE::THOMPSON |
|________________________________________________________________________|
| Unit(s) to be changed: T1001-YA, T1001-00 CPU MODULE |
| Product family affected: SCORPIO 82xx/83xx |
| F/S affected: Yes |
| Where used: KA825 and KA820 |
|________________________________________________________________________|
| Function of new microcode: |
| |
| KA825.SYS and KAINIT2.SYS have been updated to include the |
| latest patch file (KA0029.PAT). This patch file includes the |
| following fixes: |
| |
| 1. POLYH instruction calculated incorrectly |
| 2. Floating point underflow exception during POLYH instruction |
| 3. Error bit set incorrectly after system passes self-test |
| 4. Incorrect status when examining non-existent unibus address |
| 5. Lack of console functionality to support examining multiple |
| addresses |
| 6. Slave-only non-memory device incorrectly flagged as failing |
| self-test |
|________________________________________________________________________|
| Break-in/Effectivity |
| Formal SDC Release 36 date - July 17, 1989 |
| Code to be implemented on or before the specified date: |
| |
| SGO - June 30, 1989 |
| KAO - June 30, 1989 |
| FSL-ARC - July 17, 1989 |
|________________________________________________________________________|
| Quick Check: |
| At the system console prompt, examining the internal time stamp |
| register 3C, should display the following data if the code has been |
| successfully loaded: |
| >>> E/I 3C 03061355 |
|________________________________________________________________________|
| PLANT CONTACTS: PHONE |
| LOC DTN-Ext. dd-mm-yy |
| |
|Ucode Developer :________________ TWO 247-2088 |
| Carrie Thompson |
| |
|TSA Support :________________ ACO 232-2203 |
| Cary Hobson |
| |
|Manufacturing :________________ SGO 721-2410 |
| Horacio Mourino |
| |
| :________________ KAO 621-2055 |
| Dave Wilson |
| |
|Field Service :________________ DAS 275-3299 |
| Paul Deon |
|________________________________________________________________________|
________________________________________________________________________
| | |
| | SDC Release No: 36 Sheet 2 of 2 |
| ## ## ## ## ## |________________________________________|
| ## # # ## ## ## # ## | |
| ## # ## ## ## # ## | S C O R P I O |
| ## ## ## ## # # | |
| ## ## ## ## ## |________________________________________|
| | Microcode Implementation Notice |
|_______________________________|________________________________________|
| |
| OLD NEW |
| REV REV |
| --- --- |
| SDC Release 34 36 |
| Affected REVS: |
| 1. KA825.sys (CPU REV: 18) 2.9 3.0 |
| 2. KAINIT2.sys (CPU REV: 5) 2.1 2.2 |
| 3. KA00**.PAT 28 29 |
|________________________________________________________________________|
| | REVISION MATRIX: * Indicates a change from last MIN |
| |______________________________________________________________________|
| | Description R E V I S I O N |
| |______________________________________________________________________|
| | | | | | | | | | |
| | SDC RELEASE |31 |31A |32 |33 |34 |35 |36 | |
| |________________________|_____|_____|_____|_____|_____|_____|_____|___|
| | Patch Rev (KA00**.PAT) |24 |25 |25 |27 |28 |28 |29 |* |
| | KA825.SYS |2.6 |2.7 |2.7 |2.8 |2.9 |2.9 |3.0 |* |
| | KAINIT2.SYS |1.8 |1.9 |1.9 |2.0 |2.1 |2.1 |2.2 |* |
| | EBUCA (EEPROM UTIL) |2.4 |2.4 |2.4 |2.4 |2.5 |2.5 |2.5 | |
| | EBSAA (VDS) |10.10|10.10|10.11|11.02|11.04|11.04|11.04| |
| | CSBOOKA |101 |101 |101 |101 |101 |101 |101 | |
| | MUBOOKA |102 |102 |102 |102 |102 |102 |102 | |
| | ETBOOKA |104 |104 |104 |104 |104 |104 |104 | |
| | DUBOOKA |201 |201 |201 |201 |201 |201 |201 | |
| |________________________|_____________________________________________|
| | DATE |15 |16 |N C |15 |16 |N C |17 | |
| | |FEB |MAR |O H |AUG |JAN |O H |JUL | |
| | |88 |88 | A |88 |89 | A |89 | |
| | | | | N | | | N | | |
| | | | | G | | | G | | |
| | | | | E | | | E | | |
|_|________________________|_____|_____|_____|_____|_____|_____|_____|___|
| |
| MANUFACTURING IMPLEMENTATION INFORMATION: (To be returned by SGO) |
| |
| |
| Date Implemented: Verified By (Engineer): |
| |
| FF333 ________________ _______________________ |
| L260 ________________ _______________________ |
| QV ________________ _______________________ |
| |
| Date Code of first module Manufactured with this Release __________ |
| |
|________________________________________________________________________|
|
| 29.3 | determing SCORPIO boot device | KERNEL::ROBB | | Fri Oct 13 1989 09:59 | 37 |
| Finding 8200 boot device by examining EEPROM locations
Example of when it may be useful
>>>t
#ABCDEFGHIJK.MN#
. . 2 . -4 . 6 7 8 9 A B C D E . !Node 4 failed self test
02000000
?01
PC = 00000002
>>>e/p/l 20008000 !Look and see what node 4 is
P 20008000 FF1CFFFF !Ops Too broke to even laod device type
!Possible boot device. Here is how to
!look
>>>e/p/w 2009c000 ASCII
P 2009C000 4030 0
>>>e ^^
\_______Ascii code of boot dev
P 2009C002 4034 4
>>>e ^^
P 2009C004 4055 U
>>>e ^^
P 2009C006 4044 D
^^
!Note. use only the lower byte
The boot device is a DU40 therefore node 4 has to be a KDB50
^^^^ ^^^^^
|
| 29.4 | revision levels on scorpios | KERNEL::ROBB | | Mon Nov 13 1989 14:03 | 36 |
| Hello all,
We seem to be still having a number of problems on 8200/8250 and
8300/8350 because the field are still not doing FCO's or upgrading the
microcode patches.
Whenever you get a call on any of the above systems please check the SID.
For 8200, 8300 (KA820) (T1001)
The acceptable values are 05283914 or 05283b14 for rev E and patches
28 or 29. ^^^^ ^^^^
If you have anything other than the 28 then the module(s) need to be replaced.
If you have anything other than the 39 or 3b then the ka0029.pat needs to be
installed.
For 8250, 8350 (KA825) (T1001-ya)
The acceptable values are 05903914 or 05903b14 for rev B and patches
28 or 29. ^^^^ ^^^^
If you have anything other than the 90 then the module(s) need to be replaced.
If you have anything other than the 39 or 3b then the ka0029.pat needs to be
installed.
The patch can be installed remotely if you wish. You will find ka0029.pat in
RDC$COMMON. If you do not wish to install it then just copy it down to the
sysmaint account on the customers system for a branch engineer to install.
Remember if you do install it yourself you need to type T <CR>
at the >>> prompt. This will invoke the new code.
Regards,
Ken.
|
| 29.5 | Scorpio console supports E/N:xx with KA29/.PAT | KERNEL::BLAND | toward 2000 ... | Mon Feb 05 1990 06:41 | 38 |
| Subj: 82XX/83XX Console enhancement Diag Rel 36
TITLE: Console Microcode Functionality DATE: 12-13-89
AUTHOR: Jim Vermette TD #: 000152
DTN: 240-6496
ENET: VOLKS::VERMETTE CROSS REFERENCE #'s:
DEPARTMENT: MID-RANGE CSSE (PRISM/TIME/CLD#'s)
INTENDED AUDIENCE: U.S./EUROPE/GIA PRIORITY LEVEL:2
(U.S./EUROPE/GIA) (1=TIME CRITICAL,
2=NON-TIME CRITICAL)
=====================================================================
An enhancement to the 82XX/83XX Console Microcode has been
made to allow the user to examine or deposit to multiple addresses
with the /N qualifier.
As of Diagnostic Release 36 Utility Program Floppy BL-FG80P-ME
will contain this functionality. Loading KA0029.PAT or either KA825.SYS,
KAINIT2.SYS will allow the usage of the /N qualifier.
Example:
>>>E/P/L/N:4 200
P 00000200 00000000
P 00000204 00000000
P 00000208 00000000
P 0000020C 00000000
>>>E/P/L 200/N:4 Returns the same result.
>>>E/N: Will Loop until halted by Control^P.
Note: The deposit command will work in the same fashion.
*** DIGITAL INTERNAL USE ONLY ***
|