Conference azur::mcc

4432.0. "Fddi statistics" by SWTHOM::NOBRE (Jocelyne Nobre - CST France) Mon Jan 25 1993 08:21

	My customer want to use Performance Analyser on the Fddi Line of
	a DECbridge 600.He want to put alarm on percentage utilization.

	With the command :
	mcc>sho bridge pat line 1 all statis

Bridge KBANON_NS:.pat LINE 1
AT 25-JAN-1993 14:03:38 Statistics

Examination of attributes shows:
                               Duration = 59 Seconds
             Count of Total Frames Sent = 7260
         Count of Total Frames Received = 43
              Originating Bridge Frames = 1.21 Percent
              Terminating Bridge Frames = 39.53 Percent
                        Filtered Frames = 0 Percent
                    Network Utilization = -- Attribute Not Available
                  Multicast Utilization = -- Attribute Not Available
         Single Destination Utilization = -- Attribute Not Available
          Single Destination Throughput = 1.41 Percent
                  Multicast Throuhghput = 98.59 Percent
		...................................

	 the Network Utilization Attribute is not available.

	I understand , reading releases notes of ELM AM , that bridge
	performance analyser is only available for bridge ETHERNET line.
	Is it true ?
	There is a question about that in 4095 note ; I check the Fddi
	conference but there is no reply for that question.
	Is it possible through ELM AM to do some statistics on Fddi line  of
	DECbridge 5xx and 6xx ?

	Thanks for help,
	Regard,
	JOcelyne.

	other informations : command
	mcc> sho bridge pat all char	
	mcc> sho bridge pat line 1 all char


	 mcc> sho bridge pat all char
	Bridge KBANON_NS:.pat
AT 25-JAN-1993 14:20:37 Characteristics

Examination of attributes shows:
                          Hardware Type = DEFEB DECbridge 620
                            ROM Version = V2.9.0
   Device Configuration Error Condition = False
                   Device Configuration = ( (
                                   FRU Type = AP Card,
                                  FRU State = Working,
                                     FRU ID = N/A,
                               FRU Revision = Revision 8 ),
                                            (
                                   FRU Type = Three NI Card,
                                  FRU State = Working,
                                     FRU ID = N/A,
                               FRU Revision = Revision 8 ),
                                            (
                                   FRU Type = FI Card,
                                  FRU State = Working,
                                     FRU ID = N/A,
                               FRU Revision = Revision 8 ),
                                            (
                                   FRU Type = QM Card,
                                  FRU State = Working,
                                     FRU ID = N/A,
                               FRU Revision = Revision 0 ),
                                            (
                                   FRU Type = Fan,
                                  FRU State = Working,
                                     FRU ID = N/A,
                               FRU Revision = Revision 0 ) )
          IEEE802 Spanning Tree Version = V0.0.0
                                     ID = %X08002B1E1BDE
            LB100 Spanning Tree Version = V0.2.0
                             Port Count = 4
                          Root Priority = 128
                        Bad Hello Limit = 15
               Bad Hello Reset Interval = 5
             Port Test Passed Threshold = 10
                     Port Test Interval = 60 Seconds
                      No Frame Interval = 300 Seconds
                         Hello Interval = 1 Seconds
                            Listen Time = 15 Seconds
                       Forwarding Delay = 30 Seconds
                         Last Load Host = 00-00-00-00-00-00
                  Reset Defaults Switch = False
                          Update Switch = False
                IP Fragmentation Switch = True
                        LB100 Poll Time = 300 Seconds
                 LB100 Response Timeout = 15 Seconds
      LB100 Spanning Tree Compatibility = Auto-Select
                             IP Address = 16.189.144.43
                       Software Version = "V1.2"
                              NTP Table = { 80-F3 }

MCC> sho bridge pat line 1 all char

Bridge KBANON_NS:.pat LINE 1
AT 25-JAN-1993 14:24:09 Characteristics

Examination of attributes shows:
                          Datalink Type = FDDI Ring
                             Line Speed = 100000000 bps
                                Port ID = "1"
                           Port Address = 08-00-2B-1E-1B-DE
                              Port Cost = 10
                            Manual Mode = False
                         Disable Switch = False
         Management Sets Allowed Switch = True
                            Maximum TRT = 173.015 ms
                          Requested TRT = 7.9872 ms
                Valid Transmission Time = 2.62144 ms
                       Datalink Version = V1.0.0
                     SMT Resource Index = 3
                Ring Purger Enable Flag = True
                       I-Max Expiration = 40 ms
           Optical Bypass Insert Policy = True
   Entity Coordination Management State = In
                           Station Type = Dual Attachment Station
                         SMT Station ID = %X000008002B1E1BDE
                         SMT Version ID = 1
                 SMT Maximum Version ID = 1
                 SMT Minimum Version ID = 1
        Default Ethernet Type Filtering = False
                  Default SAP Filtering = False
                 Default SNAP Filtering = False
                       Frame Strip Mode = Frame Content Independent
                 Optical Bypass Present = No