| Title: | DECmcc user notes file. Does not replace IPMT. |
| Notice: | Use IPMT for problems. Newsletter location in note 6187 |
| Moderator: | TAEC::BEROUD |
| Created: | Mon Aug 21 1989 |
| Last Modified: | Wed Jun 04 1997 |
| Last Successful Update: | Fri Jun 06 1997 |
| Number of topics: | 6497 |
| Total number of notes: | 27359 |
Hello,
I have just installed DECmcc V1.2 and I'm trying to register some
TCP/IP nodes but I get the following message:
==================================================================
MCC> register snmp msumgr address 16.192.96.58
SNMP ROMMCC_NS:.msumgr
AT 29-OCT-1992 16:34:08
Partial registration success. Please retry later to complete the
registration.
Reason for Partial Registration = Identifier attributes for
unreachable
entity are:
Registered Name = ROMMCC_NS:.msumgr
Address = 16.192.96.58
Name = MSUMGR
MCC>
=======================================================================
MSUMGR is a DS3100 running ULTRIX V4.1
Note that UCX loop MSUMGR runs without problems.
I get the same problem also running the REGISTRATION from DEC-window
toolbox
I tried also the following tests:
==================================================
$ mana/enter
DECmcc (V1.2.0)
MCC> TEST SNMP MSUMGR
SNMP MSUMGR
AT 29-OCT-1992 16:30:01
Test successful.
MCC> TEST SNMP MSUMGR
SNMP MSUMGR
AT 29-OCT-1992 16:30:04
Test unsuccessful: no answer from host.
MCC>
=====================================================
I'm not able to understand why the first TEST runs without any problem and
the second (and the following also) fails.
Note that sometimes (without any special condition) the TEST command runs
without any problem ..........
In the SYSTARTUP_V5.COM UCX starts before DECmcc.
UCX is configured as follows:
UCX> sho interfaces
Interface: SE0
IP_Addr: 16.192.96.47 NETWRK: 255.0.0.0 BRDCST: 16.255.255.
255
Ethernet_Addr: AA-00-04-00-10-BB MTU: 1500
Flags: UP BRDCST NOTRL RUN
RECEIVE SEND
Packets 371 118
IP packets 226 101
Broadcast IP packets 22 0
Trailer 1 IP packets 0
Trailer 2 IP packets 0
ARP packets 3 0
Broadcast ARP packets 120 17
Drops
IP packets 0 0
ARP packets 0 0
Errors
Hardware 0 0
Software 0 0
Restarting attempts 0
Successful restarts 0
Interface: LO0
IP_Addr: 127.0.0.1 NETWRK: 255.0.0.0 BRDCST:
Ethernet_Addr: MTU: 65535
Flags: UP LOOP
RECEIVE SEND
Packets 0 0
IP packets 0 0
Broadcast IP packets 0 0
Trailer 1 IP packets 0
Trailer 2 IP packets 0
ARP packets 0 0
Broadcast ARP packets 0 0
Drops
IP packets 0 0
ARP packets 0 0
Errors
Hardware 0 0
Software 0 0
Restarting attempts 0
Successful restarts 0
UCX> sho config snmp/full
SNMP Configuration
Services: 127
Contact: not defined
Location
First: Roma Magliana, piano terra, I.S.
Community Type Address_list
public Read 0.0.0.0
UCX> show route
DYNAMIC database
Type Destination Gateway
AH 127.0.0.1 127.0.0.1
AN 0.0.0.0 16.192.96.47
AN 16.0.0.0 16.192.96.47
UCX>
Could somebody help me, please?
| T.R | Title | User | Personal Name | Date | Lines |
|---|---|---|---|---|---|
| 3992.1 | SNMP agent? | TOOK::MINTZ | LKG2-2 near pole X3, cube 6072, dtn 226-5033 | Thu Oct 29 1992 11:28 | 6 |
Is there an SNMP agent running on the system that you are trying to register? UCX loop just checks to see if the system is reachable via IP/ICMP; it does not check for an SNMP agent. | |||||
| 3992.2 | what kind of problem is it? | ROMTSS::GALLANA | Thu Oct 29 1992 12:21 | 26 | |
At 6 o'clock (local time) I was able to register both nodes
(MSUMGR - ULTRIX with SNMP and
ROMTSS - VMS V5.4.3 with UCX v2.0 , SNMP agent also)
Note that I didn't do anything special to make it working
After that I closed DECmcc and I activated it again...
(I tried with both the DECwindow inteface and the commnad interface)
it doesn't work again:
the first time I TEST the entity I get "test successfull",
the second, third, ... time and i get
"test unsuccessful: no answer from host"
If I exit and then I reenter in DECmcc I'm able to test the SNMP but
only the first time ...
What kind of problem is it?
Francesco
| |||||
| 3992.3 | is it a phantom bug? | ROMTSS::GALLANA | Thu Oct 29 1992 13:00 | 19 | |
I've tried to isolate the problem but it seems to be like a phantom:
infact entering in DECmcc I'm not able to SHO CHARACTERISTICS
I get the message
Internet communication device error %NONAME-W-NOMSG,
Messge number 000000
but sometime, doing DIRECTORY or SHOW STATISTICS they runs
after that I'm able to do everything: SHOW .... TEST ... GRAPH..
it it a phantom?
I'll try tomorrow to reinstall DNS and DECmcc and UCX
bye
| |||||
| 3992.4 | What version of UCX are you running? | TOOK::GUERTIN | Don't waffle (unless you want to) | Thu Oct 29 1992 13:01 | 0 |
| 3992.5 | UCX T2.0-21 | ROMOIS::GALLANA | Fri Oct 30 1992 03:16 | 2 | |
mage file identification: "UCX T2.0-21"
| |||||
| 3992.6 | UDP TIMEOUT? | VCSESU::WADE | Bill Wade, VAXc Systems & Support Eng | Fri Oct 30 1992 09:36 | 7 |
Just a shot in the dark but you may want to try increasing the the UDP
timeout from the default of 5 seconds. I've found that 5 seconds is an
optimistic value at times.
mcc> set mcc 0 tcpip udp timeout 30
| |||||
| 3992.7 | UDP = 30 doesn't solve the problem | ROMOIS::GALLANA | Fri Oct 30 1992 10:34 | 4 | |
no way, the first TEST command runs, the second ...etc... fail
UDP doesn't solve the problem
| |||||
| 3992.8 | Why field test? | TOOK::MINTZ | LKG2-2 near pole X3, cube 6072, dtn 226-5033 | Fri Oct 30 1992 11:38 | 4 |
Someone more familiar with the module will probably answer, but I would certainly be concerned about results based on a field test version of UCX. Can you upgrade to the SSB version? | |||||
| 3992.9 | SSB version of UCX020 works | ROMOIS::GALLANA | Mon Nov 02 1992 05:41 | 7 | |
I just installed SSB version of UCX
Now everything works
Many thanks for YOUR cooperation
Francesco
| |||||