Conference azur::mcc

3414.0. "Accvio with Autoconfiguration" by BALZAC::PETIT (Bruno Petit/Evry-FRANCE) Thu Jul 23 1992 04:57

Yesterday I installed BMS V1.2 on a VMS 5.5 system and begun to use DECmcc; I
had some messages (I didn't see them immediatly):

..........................................................;;.................
$ manage/enter/inter=decw
X Toolkit Warning: BadMatch (invalid parameter attributes)
%DEBUGBOOT-W-EXQUOTA, exceeded quota
%XLIB-E-INSFMEM, insufficient dynamic memory
%DEBUGBOOT-W-EXQUOTA, exceeded quota
%XLIB-E-INSFMEM, insufficient dynamic memory
%DEBUGBOOT-W-EXQUOTA, exceeded quota
%CMA-F-EXCCOP, exception raised; VMS condition code follows
-SYSTEM-F-ACCVIO, access violation, reason mask=04, virtual address=00000000, PC
=003A2CE7, PSL=0BC00009
$ manage/enter/inter=decw
$ manage/enter/inter=decw
%DEBUGBOOT-W-EXQUOTA, exceeded quota
%CMA-F-EXCCOP, exception raised; VMS condition code follows
-SYSTEM-F-INSFMEM, insufficient dynamic memory
...............................................................................

I run an AUTOCONF (Phase IV) , It started fine, and later on I cancelled it.
When I tried to run a new AutoConf I got a TRM-FAILURE , just when DECmcc
is  "Checking the namespace.  This will take a moment.  Please wait..."

This morning I started again DECmcc, tried to run an AUTOCONF  and got an 
AccVio.

................................................................................

        Welcome to DECnet Phase IV Autoconfiguration

        Type '?' for Help or 'Q' to Quit, at any of the prompts.


        Checking the namespace.  This will take a moment.  Please wait...
troubles:
%SYSTEM-F-ACCVIO, access violation, reason mask=04, virtual address=00000044, PC
=00078B54, PSL=03C00004

  Improperly handled condition, image exit forced.

        Signal arguments              Stack contents

        Number = 00000005                00000000
        Name   = 0000000C                00000000
                 00000004                00000000
                 00000044                00000000
                 00078B54                27FC0000
                 03C00004                7FEAAFEC
                                         7FEAAFC8
                                         0007AA93
                                         0006AD0C
                                         00083A98

        Register dump

        R0 = 00000000  R1 = 0013F0B4  R2 = 0006AD80  R3 = 0006AD80
        R4 = 00000000  R5 = 00084080  R6 = 00000000  R7 = 0006A998
        R8 = 000841BC  R9 = 00083C54  R10= 00000006  R11= 7FFE2BDC
        AP = 7FEAAD34  FP = 7FEAACF4  SP = 7FEAAD70  PC = 00078B54
        PSL= 03C00004

%DCL-W-SKPDAT, image data (records not beginning with "$") ignored

        Error:  An error has occurred.

        Warning:  DECnet Phase IV Autoconfiguration data files
                  may be corrupt.

        DECnet Phase IV Autoconfiguration exiting under error conditions.

o  Press RETURN to exit:



Regards.

Bruno.

	Hello Bruno,

	It seems like all your problems are linked to insufficient
	dynamic memory.  Have you run MCC_COMMON:MCC_AUDIT.COM to
	check your account quotas and system parameters to insure
    	that they meet the requirements of DECmcc?

	The error you got while running Autoconfiguration happened
	while Autoconfiguration asked DECmcc to execute the
	command "SHOW MCC 0" or "SHOW MCC 0 ALL CHAR".  Again,
	this problem seems to be a more general one, not
	something specific to Autoconfiguration.

	Execute MCC_COMMON:MCC_AUDIT.COM while logged into the
	account from which you ran your tests and let us 
	know the results.  

	Thanks,

	Ulla Figwer

Thanks for your advise. I've run the procedure and some of SYSGEN
parameters were too low. 

I'm going to adjust them and if I still have the problem, I will post a new reply.

Bruno.