[Search for users]
[Overall Top Noters]
[List of all Conferences]
[Download this site]
| Title: | FDDI - The Next Generation |
|
| Moderator: | NETCAD::STEFANI |
|
| Created: | Thu Apr 27 1989 |
| Last Modified: | Thu Jun 05 1997 |
| Last Successful Update: | Fri Jun 06 1997 |
| Number of topics: | 2259 |
| Total number of notes: | 8590 |
1933.0. "problems with DEMFA & VAX 6310!!" by MXOC00::MREYES () Wed Jan 24 1996 19:38
The problem that i have is the following:
My customer "Iberoamericana" University have a VAX 6310 with 32Mb RAM,
Open VMS 6.1 and recently has been introduced a DEC FDDI controller 400
(DEMFA-AA), the driver for this adapter is loaded OK, and at this point the
system is reconfigured by DECNET (the circuit was defined and enabled), at the
moment that the system is working with the new circuit (FDDI card), the
transmision rate is lower than the ethernet circuit BNA-0. By other hand ,
after of this installation, the customer have experienced problems with LAT and
Decnet, some problems are: users cannot connect to the system via LAT until
that the service LAT$LINK is dropped from LATCP, and the circuit bna-0
adjacency is down in several times. By this problems, the circuit was disabled
and the ethernet circuit was enabled again.
The customer tell to me that in a few months a Digital distributor
lend to him a memory card with 128 MB, this card was recognized in console
mode and in the OVMS environment, but after of two or tree hours the system
was reinitialized without any process that's make this behaviour. By this
thing, was decided that the memory card was out of the system VAX 6310.
At the colole prompt i have obtaoned this information:
>>>show config
1+ KA62B (8001) 8004
A+ MS62A (4001) 0002
C+ ????? ( 823) 520
D+ DWMBA/A (2001) 0002
E+ DWMBA/A (2001) 0002
XBI D
1+ DWMBA/B (2107) 000A
6+ DEBNA (410F) 0256
XBI E
1+ DWMBA/B (2107) 000A
2+ KLESI-B (0103) 0006
3+ DMB32 (0109) 220D
4+ KDB50 (010E) 141F
>>>INIT
ROM=4.1
EEPROM=2.0/4.3
F E D C B A 9 8 7 6 5 4 3 2 1 0 Node #
. A A A . M . . . . . . . . P TYP
. o o + + + STF
. B BPD
. + ETF
. B BPD
. + + XBI D+
. + + + + + XBI E+
A1 ILV
32 32 MB
I have checked in the tima articles and i found a matrix for the cosole
revision and patches, if i upgrade this, could this affect the behaviour
of the fddi controller?
in OVMS ha have checked in the SDA utility and the LSB$L_MFA_DEV doesn't exist.
the following is information of the system:
NCP>SH EXEC CHAR
Node Volatile Characteristics as of 23-JAN-1996 18:06:11
Executor node = 1.1 (UIMX1)
Identification = DECnet for OpenVMS VAX V6.1
Management version = V4.0.0
Incoming timer = 45
Outgoing timer = 60
Incoming Proxy = Enabled
Outgoing Proxy = Enabled
NSP version = V4.1.0
Maximum links = 32
Delay factor = 80
Delay weight = 5
Inactivity timer = 60
Retransmit factor = 10
Routing version = V2.0.0
Type = area IV
Routing timer = 600
Broadcast routing timer = 180
Maximum address = 1023
Maximum circuits = 16
Maximum cost = 1022
Maximum hops = 30
Maximum visits = 63
Maximum area = 63
Max broadcast nonrouters = 64
Max broadcast routers = 32
Maximum path splits = 1
Area maximum cost = 1022
Area maximum hops = 30
Maximum buffers = 100
Buffer size = 576
Default access = incoming and outgoing
Pipeline quota = 4032
Alias maximum links = 32
Path split policy = Normal
Maximum Declared Objects = 31
NCP>SH K LINKS
Known Link Volatile Summary as of 23-JAN-1996 18:06:17
Link Node PID Process Remote link Remote user
24633 1.1 (UIMX1) 202004B7 GCHOPE 24634 CTERM
24634 1.1 (UIMX1) 20200116 REMACP 24633 GCHOPE
16805 1.1 (UIMX1) 202003A7 _LTA5194: 16806 CTERM
16806 1.1 (UIMX1) 20200116 REMACP 16805 MARTINEFER
24619 1.7 (CHAAC) 20200504 _LTA5295: 8639 145
16689 1.7 (CHAAC) 2020039E JMGCES 8348 145
16436 1.60 (LPSDIN) 2020011A LPS_LPSDIN 28672 50
8573 1.70 (LPSDGR) 20200119 LPS_LPSDGR 1024 50
8290 3.1 (NEWTON) 2020013D AppleTalk ACP 24642 OBJ_85
NCP>SH K CIRC
Known Circuit Volatile Summary as of 23-JAN-1996 18:06:30
Circuit State Loopback Adjacent
Name Routing Node
BNA-0 on 1.300
BNA-0 9.1 (XY9000)
BNA-0 1.1010 (XYPLEX)
BNA-0 3.1 (NEWTON)
BNA-0 7.1 (PLATON)
BNA-0 4.1 (SENECA)
BNA-0 5.1 (CLIO21)
TX-0-1 on 10.1 (PUEBLA)
Known Circuit Volatile Characteristics as of 23-JAN-1996 18:07:27
Circuit = BNA-0
State = on
Service = enabled
Designated router = 1.1010 (XYPLEX)
Cost = 25
Maximum routers allowed = 33
Router priority = 64
Hello timer = 15
Type = Ethernet
Adjacent node = 1.300
Listen timer = 90
UIMX1� MCR SYSGEN AUTOCONFIG ALL
%SYSGEN-E-SYSVERDIF, system version mismatch - reassemble and relink driver
-SYSGEN-I-DRIVENAM, driver name is SIDRIVER
%SYSGEN-E-SYSVERDIF, system version mismatch - reassemble and relink driver
-SYSGEN-I-DRIVENAM, driver name is SIDRIVER
UIMX1� SH K CIRC
%DCL-W-UNDKEY, DEFAULT key CIRC is undefined
UIMX1� SH NET
VAX/VMS Network status for local node 1.1 UIMX1 on 23-JAN-1996 18:10:01.88
Area Cost Hops Next Hop to Area
1 0 0 (Local) -> 1.1 UIMX1
3 25 1 BNA-0 -> 3.1 NEWTON
4 25 1 BNA-0 -> 4.1 SENECA
5 25 1 BNA-0 -> 5.1 CLIO21
6 28 2 BNA-0 -> 9.1 XY9000
7 25 1 BNA-0 -> 7.1 PLATON
8 28 2 BNA-0 -> 9.1 XY9000
9 25 1 BNA-0 -> 9.1 XY9000
10 10 1 TX-0-1 -> 10.1 PUEBLA
30 42 3 BNA-0 -> 9.1 XY9000
Node Links Cost Hops Next Hop to Node
1.2 UXMAL 0 25 1 BNA-0 -> 1.2 UXMAL
1.3 UIMX3 0 25 1 BNA-0 -> 1.3 UIMX3
1.5 BIBLOS 0 25 1 BNA-0 -> 1.5 BIBLOS
1.6 KUKUL 0 25 1 BNA-0 -> 1.6 KUKUL
1.7 CHAAC 1 25 1 BNA-0 -> 1.7 CHAAC
1.10 DEPP01 0 25 1 BNA-0 -> 1.10 DEPP01
1.50 MCDIN1 0 25 1 BNA-0 -> 1.50 MCDIN1
1.51 0 25 1 BNA-0 -> 1.51
1.52 MCALEX 0 25 1 BNA-0 -> 1.52 MCALEX
1.59 MCDIN9 0 25 1 BNA-0 -> 1.59 MCDIN9
1.60 LPSDIN 1 25 1 BNA-0 -> 1.60 LPSDIN
1.70 LPSDGR 1 25 1 BNA-0 -> 1.70 LPSDGR
1.101 0 33 2 BNA-0 -> 1.300
1.133 0 25 1 BNA-0 -> 1.133
1.205 0 25 1 BNA-0 -> 1.205
1.209 0 25 1 BNA-0 -> 1.209
1.300 0 25 1 BNA-0 -> 1.300
1.690 0 25 1 BNA-0 -> 1.690
1.831 0 25 1 BNA-0 -> 1.831
1.902 0 25 1 BNA-0 -> 1.902
1.905 0 25 1 BNA-0 -> 1.905
1.907 0 25 1 BNA-0 -> 1.907
1.910 0 25 1 BNA-0 -> 1.910
1.911 0 25 1 BNA-0 -> 1.911
1.922 0 25 1 BNA-0 -> 1.922
1.923 0 25 1 BNA-0 -> 1.923
1.924 0 25 1 BNA-0 -> 1.924
1.925 0 25 1 BNA-0 -> 1.925
1.926 0 25 1 BNA-0 -> 1.926
1.928 0 25 1 BNA-0 -> 1.928
1.950 0 25 1 BNA-0 -> 1.950
1.1010 XYPLEX 0 25 1 BNA-0 -> 1.1010 XYPLEX
Total of 32 nodes.
at the moment of the analyze the errorlog
UIMX1� ANAL/ERROR/SINCE=23-JAN-1996
Error Log Report Generator Version V6.1
******************************* ENTRY 22373. *******************************
ERROR SEQUENCE 14821. LOGGED ON: SID 0A000005
DATE/TIME 23-JAN-1996 00:01:42.63 SYS_TYPE 02410201
SYSTEM UPTIME: 0 DAYS 17:12:42
SCS NODE: UIMX1 VAX/VMS V6.1
ADAPTER ERROR KA62B CPU FW REV# 6. CONSOLE FW REV# 4.1
XMI NODE # 1.
SW FLAG 00040002
XMI BUS ERROR
NO XMI ERROR FOUND
DWMBA DATA - XMI NODE #14.
PHYS ADR 21F00000
NODE 14.
XDEV 00022001
DWMBA
DEVICE REV = 2.
XBE 80800388
PARITY ERROR
ERROR DETECTED
XFADR 00080002
FAILING ADDR = 00080002(X)
FAILING LENGTH = 0.
AREAR 61F0000C
FAILING ADDR RESPONDER = 21F0000C(X)
RESPONDER FAILING LENGTH = 1.
AESR 80410000
XBI CABLE OK
READ CMD
FAILING COMMANDER = NODE #01(X)
AIMR 88F7A01F
IBUS CPU DATA PE INTRPT ENABLED
IBUS DMA-B C/A PE INTRPT ENABLED
IBUS DMA-A C/A PE INTRPT ENABLED
TRANSACTION TMO INTRPT ENABLED
COMMAND NOACK/NXM INTRPT ENABLED
RER INTRPT ENABLED
RSE INTRPT ENABLED
NRR INTRPT ENABLED
WR DATE NOACK INTRPT ENABLED
RD/ID DATA NOACK INTRPT ENABLED
WSE INTRPT ENABLED
PARITY ERROR INTRPT ENABLED
CORRECTED CONFIRM INTRPT ENABLED
ENABLED IVINTR TRANSACTIONS
AIVINTR 00000002
IVINTR DESTINATION = 0002(X)
ADG1 00000000
BCSR 80000017
IBUS PE INTRPT ENABLED
SELF-TEST LED
BI INTLCK RD FAILURES INTRPT ENABLED
ENABLE XBI INTERRUPTS
BESR 00000010
MS TRANSACTION FAILED
BI INTERRUPT STATUS = 0.
XBI INTERRUPT STATUS = 0.
BIDR 00000002
INTERRUPT DESTINATION = 0002(X)
DIAGNOSTIC DATA = 0000(X)
BTIM C13B97F0
BI DMA FAILING ADDR = 013B97F0(X)
FAILING LENGTH = 3.
BVOR 00000400
XBI VECTOR OFFSET = 04(X)
BVR 00000138
XBI VECTOR = 004E(X)
BDCR1 00000000
RSVD 00000000
******************************* ENTRY 22374. *******************************
ERROR SEQUENCE 14822. LOGGED ON: SID 0A000005
DATE/TIME 23-JAN-1996 00:04:48.72 SYS_TYPE 02410201
SYSTEM UPTIME: 0 DAYS 17:15:48
SCS NODE: UIMX1 VAX/VMS V6.1
TIME STAMP KA62B CPU FW REV# 6. CONSOLE FW REV# 4.1
XMI NODE # 1.
******************************* ENTRY 22375. *******************************
ERROR SEQUENCE 14823. LOGGED ON: SID 0A000005
DATE/TIME 23-JAN-1996 00:06:15.18 SYS_TYPE 02410201
SYSTEM UPTIME: 0 DAYS 17:17:15
SCS NODE: UIMX1 VAX/VMS V6.1
ADAPTER ERROR KA62B CPU FW REV# 6. CONSOLE FW REV# 4.1
XMI NODE # 1.
SW FLAG 00040002
XMI BUS ERROR
NO XMI ERROR FOUND
DWMBA DATA - XMI NODE #14.
PHYS ADR 21F00000
NODE 14.
XDEV 00022001
DWMBA
DEVICE REV = 2.
XBE 80800388
PARITY ERROR
ERROR DETECTED
XFADR 00080002
FAILING ADDR = 00080002(X)
FAILING LENGTH = 0.
AREAR 61F0000C
FAILING ADDR RESPONDER = 21F0000C(X)
RESPONDER FAILING LENGTH = 1.
AESR 80410000
XBI CABLE OK
READ CMD
FAILING COMMANDER = NODE #01(X)
AIMR 88F7A01F
IBUS CPU DATA PE INTRPT ENABLED
IBUS DMA-B C/A PE INTRPT ENABLED
IBUS DMA-A C/A PE INTRPT ENABLED
TRANSACTION TMO INTRPT ENABLED
COMMAND NOACK/NXM INTRPT ENABLED
RER INTRPT ENABLED
RSE INTRPT ENABLED
NRR INTRPT ENABLED
WR DATE NOACK INTRPT ENABLED
RD/ID DATA NOACK INTRPT ENABLED
WSE INTRPT ENABLED
PARITY ERROR INTRPT ENABLED
CORRECTED CONFIRM INTRPT ENABLED
ENABLED IVINTR TRANSACTIONS
AIVINTR 00000002
IVINTR DESTINATION = 0002(X)
ADG1 00000000
BCSR 80000017
IBUS PE INTRPT ENABLED
SELF-TEST LED
BI INTLCK RD FAILURES INTRPT ENABLED
ENABLE XBI INTERRUPTS
BESR 00000010
MS TRANSACTION FAILED
BI INTERRUPT STATUS = 0.
XBI INTERRUPT STATUS = 0.
BIDR 00000002
INTERRUPT DESTINATION = 0002(X)
DIAGNOSTIC DATA = 0000(X)
BTIM C08261F0
BI DMA FAILING ADDR = 008261F0(X)
FAILING LENGTH = 3.
BVOR 00000400
XBI VECTOR OFFSET = 04(X)
BVR 00000138
XBI VECTOR = 004E(X)
BDCR1 00000000
RSVD 00000000
******************************* ENTRY 22376. *******************************
ERROR SEQUENCE 14824. LOGGED ON: SID 0A000005
DATE/TIME 23-JAN-1996 00:06:39.61 SYS_TYPE 02410201
SYSTEM UPTIME: 0 DAYS 17:17:39
SCS NODE: UIMX1 VAX/VMS V6.1
ADAPTER ERROR KA62B CPU FW REV# 6. CONSOLE FW REV# 4.1
XMI NODE # 1.
SW FLAG 00040002
XMI BUS ERROR
NO XMI ERROR FOUND
DWMBA DATA - XMI NODE #14.
PHYS ADR 21F00000
NODE 14.
XDEV 00022001
DWMBA
DEVICE REV = 2.
XBE 80800388
PARITY ERROR
ERROR DETECTED
XFADR 00080002
FAILING ADDR = 00080002(X)
FAILING LENGTH = 0.
AREAR 61F0000C
FAILING ADDR RESPONDER = 21F0000C(X)
RESPONDER FAILING LENGTH = 1.
AESR 80410000
XBI CABLE OK
READ CMD
FAILING COMMANDER = NODE #01(X)
AIMR 88F7A01F
IBUS CPU DATA PE INTRPT ENABLED
IBUS DMA-B C/A PE INTRPT ENABLED
IBUS DMA-A C/A PE INTRPT ENABLED
TRANSACTION TMO INTRPT ENABLED
COMMAND NOACK/NXM INTRPT ENABLED
RER INTRPT ENABLED
RSE INTRPT ENABLED
NRR INTRPT ENABLED
WR DATE NOACK INTRPT ENABLED
RD/ID DATA NOACK INTRPT ENABLED
WSE INTRPT ENABLED
PARITY ERROR INTRPT ENABLED
CORRECTED CONFIRM INTRPT ENABLED
ENABLED IVINTR TRANSACTIONS
AIVINTR 00000002
IVINTR DESTINATION = 0002(X)
ADG1 00000000
BCSR 80000017
IBUS PE INTRPT ENABLED
SELF-TEST LED
BI INTLCK RD FAILURES INTRPT ENABLED
ENABLE XBI INTERRUPTS
BESR 00000010
MS TRANSACTION FAILED
BI INTERRUPT STATUS = 0.
XBI INTERRUPT STATUS = 0.
BIDR 00000002
INTERRUPT DESTINATION = 0002(X)
DIAGNOSTIC DATA = 0000(X)
BTIM C08FB7F0
BI DMA FAILING ADDR = 008FB7F0(X)
FAILING LENGTH = 3.
BVOR 00000400
XBI VECTOR OFFSET = 04(X)
BVR 00000138
XBI VECTOR = 004E(X)
BDCR1 00000000
RSVD 00000000
******************************* ENTRY 22377. *******************************
ERROR SEQUENCE 14825. LOGGED ON: SID 0A000005
DATE/TIME 23-JAN-1996 00:10:12.47 SYS_TYPE 02410201
SYSTEM UPTIME: 0 DAYS 17:21:12
SCS NODE: UIMX1 VAX/VMS V6.1
ADAPTER ERROR KA62B CPU FW REV# 6. CONSOLE FW REV# 4.1
XMI NODE # 1.
SW FLAG 00040002
XMI BUS ERROR
NO XMI ERROR FOUND
DWMBA DATA - XMI NODE #14.
PHYS ADR 21F00000
NODE 14.
XDEV 00022001
DWMBA
DEVICE REV = 2.
XBE 80800388
PARITY ERROR
ERROR DETECTED
XFADR 00080002
FAILING ADDR = 00080002(X)
FAILING LENGTH = 0.
AREAR 61F0000C
FAILING ADDR RESPONDER = 21F0000C(X)
RESPONDER FAILING LENGTH = 1.
AESR 80410000
XBI CABLE OK
READ CMD
FAILING COMMANDER = NODE #01(X)
AIMR 88F7A01F
IBUS CPU DATA PE INTRPT ENABLED
IBUS DMA-B C/A PE INTRPT ENABLED
IBUS DMA-A C/A PE INTRPT ENABLED
TRANSACTION TMO INTRPT ENABLED
COMMAND NOACK/NXM INTRPT ENABLED
RER INTRPT ENABLED
RSE INTRPT ENABLED
NRR INTRPT ENABLED
WR DATE NOACK INTRPT ENABLED
RD/ID DATA NOACK INTRPT ENABLED
WSE INTRPT ENABLED
PARITY ERROR INTRPT ENABLED
CORRECTED CONFIRM INTRPT ENABLED
ENABLED IVINTR TRANSACTIONS
AIVINTR 00000002
IVINTR DESTINATION = 0002(X)
ADG1 00000000
BCSR 80000017
IBUS PE INTRPT ENABLED
SELF-TEST LED
BI INTLCK RD FAILURES INTRPT ENABLED
ENABLE XBI INTERRUPTS
BESR 00000010
MS TRANSACTION FAILED
BI INTERRUPT STATUS = 0.
XBI INTERRUPT STATUS = 0.
BIDR 00000002
INTERRUPT DESTINATION = 0002(X)
DIAGNOSTIC DATA = 0000(X)
BTIM C00594B0
BI DMA FAILING ADDR = 000594B0(X)
FAILING LENGTH = 3.
BVOR 00000400
XBI VECTOR OFFSET = 04(X)
BVR 00000138
XBI VECTOR = 004E(X)
BDCR1 00000000
RSVD 00000000
. . .
. . .
. . .
******************************* ENTRY 22378. *******************************
ERROR SEQUENCE 14833. LOGGED ON: SID 0A000005
DATE/TIME 23-JAN-1996 00:24:48.72 SYS_TYPE 02410201
SYSTEM UPTIME: 0 DAYS 17:35:48
SCS NODE: UIMX1 VAX/VMS V6.1
TIME STAMP KA62B CPU FW REV# 6. CONSOLE FW REV# 4.1
XMI NODE # 1.
******************************* ENTRY 22386. *******************************
ERROR SEQUENCE 14834. LOGGED ON: SID 0A000005
DATE/TIME 23-JAN-1996 00:26:04.74 SYS_TYPE 02410201
SYSTEM UPTIME: 0 DAYS 17:37:04
SCS NODE: UIMX1 VAX/VMS V6.1
ADAPTER ERROR KA62B CPU FW REV# 6. CONSOLE FW REV# 4.1
XMI NODE # 1.
SW FLAG 00040002
XMI BUS ERROR
NO XMI ERROR FOUND
DWMBA DATA - XMI NODE #14.
PHYS ADR 21F00000
NODE 14.
XDEV 00022001
DWMBA
DEVICE REV = 2.
XBE 80800388
PARITY ERROR
ERROR DETECTED
XFADR 00080002
FAILING ADDR = 00080002(X)
FAILING LENGTH = 0.
AREAR 61F0000C
FAILING ADDR RESPONDER = 21F0000C(X)
RESPONDER FAILING LENGTH = 1.
AESR 80410000
XBI CABLE OK
READ CMD
FAILING COMMANDER = NODE #01(X)
AIMR 88F7A01F
IBUS CPU DATA PE INTRPT ENABLED
IBUS DMA-B C/A PE INTRPT ENABLED
IBUS DMA-A C/A PE INTRPT ENABLED
TRANSACTION TMO INTRPT ENABLED
COMMAND NOACK/NXM INTRPT ENABLED
RER INTRPT ENABLED
RSE INTRPT ENABLED
NRR INTRPT ENABLED
WR DATE NOACK INTRPT ENABLED
RD/ID DATA NOACK INTRPT ENABLED
WSE INTRPT ENABLED
PARITY ERROR INTRPT ENABLED
CORRECTED CONFIRM INTRPT ENABLED
ENABLED IVINTR TRANSACTIONS
AIVINTR 00000002
IVINTR DESTINATION = 0002(X)
ADG1 00000000
BCSR 80000017
IBUS PE INTRPT ENABLED
SELF-TEST LED
BI INTLCK RD FAILURES INTRPT ENABLED
ENABLE XBI INTERRUPTS
BESR 00000010
MS TRANSACTION FAILED
BI INTERRUPT STATUS = 0.
PARITY ERROR INTRPT ENABLED
CORRECTED CONFIRM INTRPT ENABLED
ENABLED IVINTR TRANSACTIONS
AIVINTR 00000002
IVINTR DESTINATION = 0002(X)
ADG1 00000000
BCSR 80000017
IBUS PE INTRPT ENABLED
SELF-TEST LED
BI INTLCK RD FAILURES INTRPT ENABLED
ENABLE XBI INTERRUPTS
BESR 00000010
MS TRANSACTION FAILED
BI INTERRUPT STATUS = 0.
XBI INTERRUPT STATUS = 0.
BIDR 00000002
INTERRUPT DESTINATION = 0002(X)
DIAGNOSTIC DATA = 0000(X)
BTIM C0057670
BI DMA FAILING ADDR = 00057670(X)
FAILING LENGTH = 3.
BVOR 00000400
XBI VECTOR OFFSET = 04(X)
BVR 00000138
XBI VECTOR = 004E(X)
BDCR1 00000000
RSVD 00000000
With this information could someone helpme.
Mario Reyes Gonz�lez
MCS
SYSTEM logged out at 23-JAN-1996 19:06:17.32
| T.R | Title | User | Personal
Name | Date | Lines |
|---|
| 1933.1 | | STRWRS::KOCH_P | It never hurts to ask... | Thu Jan 25 1996 18:10 | 7 |
|
Well, the first rule here is that you must DELETE the ethernet entries
from the DECnet database. There is information in the release notes
about this.
What version of DECnet are you running? If phase IV, this is probably
why you are encountering these problems.
|
| 1933.2 | decnet version... | MXOC00::MREYES | | Fri Jan 26 1996 09:35 | 9 |
| the version is decnet phase IV with routing and cost scheme.
exist any problem or an aditional restrictions with decnet phase IV and
FDDI 400 controller?
Mario Reyes
MCS Mexico
|