Conference decwet::windows-nt

5819.0. "Auto Answer setting file ?" by MSAPG1::ENG () Wed Mar 19 1997 20:50

    
    
    
    Hello all.
    
    I have installed a MERZ 336 modem and make it work on my Windows NT
    Workstation for RAS access by using the Driver Diskette from the
    manufacturer.
    
    Everything looks fine except that when I want to set the auto answer an
    incoming call to 9 rings by using ATS0=9&W&Y, the modem still pick up
    the incoming call immediately (default value). The reason is that I am
    using the same telephone line for dial in and telephone.
    
    I noticed that all the setting are OK, the problem only happened when I
    startup the RAS service in the control panel. From the modem log file I
    found that the system is sending the reset to factory default command
    every time the modem initialize. A small portion of the log file is as
    bellow :
    
    03-20-1997 10:09:12.908 - TNC MERZ336 HI SPEED FAX MODEM in use.
    03-20-1997 10:09:12.908 - Modem type: TNC MERZ336 HI SPEED FAX MODEM
    03-20-1997 10:09:12.918 - Modem inf path: merz3361.inf
    03-20-1997 10:09:12.918 - Modem inf section: Modem1
    03-20-1997 10:09:12.918 - 57600,N,8,1
    03-20-1997 10:09:12.918 - 57600,N,8,1
    03-20-1997 10:09:12.928 - Initializing modem.
    03-20-1997 10:09:12.928 - Send: AT<cr>
    03-20-1997 10:09:12.958 - Recv: AT<cr>
    03-20-1997 10:09:12.958 - Recv: <cr><lf>OK<cr><lf>
    03-20-1997 10:09:12.958 - Interpreted response: OK
    03-20-1997 10:09:12.978 - Send: AT &F &W<cr>           *****
    03-20-1997 10:09:12.978 - Recv: AT &F &W<cr>
    03-20-1997 10:09:13.078 - Recv: <cr><lf>OK<cr><lf>
    03-20-1997 10:09:13.078 - Interpreted response: OK
    03-20-1997 10:09:13.078 - Send: ATS7=60S30=26L1M1\N3%C1&K3B0N1X4<cr>
    03-20-1997 10:09:13.098 - Recv: ATS7=60S30=26L1M1\N3%C1&K3B0N1X4<cr>
    03-20-1997 10:09:13.098 - Recv: <cr><lf>OK<cr><lf>
    03-20-1997 10:09:13.098 - Interpreted response: OK
    03-20-1997 10:09:13.098 - Send: ats0=9&w&y<cr>
    03-20-1997 10:09:13.108 - Recv: ats0=9&w&y<cr>
    03-20-1997 10:09:13.198 - Recv: <cr><lf>OK<cr><lf>
    03-20-1997 10:09:13.198 - Interpreted response: OK
    03-20-1997 10:09:13.198 - Waiting for a call.
    03-20-1997 10:09:13.208 - Send: ATS0=0<cr>
    03-20-1997 10:09:13.208 - Recv: ATS0=0<cr>
    03-20-1997 10:09:13.208 - Recv: <cr><lf>OK<cr><lf>
    03-20-1997 10:09:13.208 - Interpreted response: OK
    03-20-1997 10:10:45.561 - Hanging up the modem.
    03-20-1997 10:10:45.571 - Send: AT&F<cr>
    03-20-1997 10:10:45.681 - Recv: AT&F<cr><cr><lf>OK<cr><lf>
    03-20-1997 10:10:45.681 - Session Statistics:
    03-20-1997 10:10:45.681 -                Reads : 104 bytes
    03-20-1997 10:10:45.681 -                Writes: 68 bytes
    03-20-1997 10:10:45.691 - Modem closed.
    
    I wonder which file keep the initializing file setting ? Anyone could
    shed some light on this will be very much appreciated.
    
    Best regards,
    -Eng-
    

    
    Oooooop.... it is MS Windows NT Workstation V4.0.
    
    Best regards,
    -Eng-